Rubber gasket
Rubber gasket
Author
Discussion

SILICONE KID

Original Poster:

14,997 posts

262 months

Friday 15th October 2010
quotequote all
Which way does the rubber gasket on the rocker cover fit?.There is a lip on one side and flat on the other side..

thrownarod

37 posts

195 months

Friday 15th October 2010
quotequote all
Put your lips against the flap and blow.

Chimpaholic

9,637 posts

210 months

Friday 15th October 2010
quotequote all
Dont listen to him Daz, he is back on the cunnilingus again!

Fit the lip to the rocker cover face, the flat goes to the head.

You will see, it fits in nicely.

Use some super-glue (not silicone, Quinny you kill me mate) to hold the gasket to the rocker cover while you fit it.

Good luck.

thrownarod

37 posts

195 months

Friday 15th October 2010
quotequote all
I prefer my method tongue out

SILICONE KID

Original Poster:

14,997 posts

262 months

Friday 15th October 2010
quotequote all
Thanks.Im tarting up the engine bay,The rocker covers are satin black(powder coated)just purchased steal braided efi 150c fuel pipe and s/steal braid for the breaher pipe and vac pipe to the plenum.Starting to look
prity.coolfits perfect.Also fitted a TVR Power thermal insulator,don`t think its going to do much ,it looks like a bit of card board..Wanted the magna parva type but they only come in 38mm ,Know good for my beast.

http://cgi.ebay.co.uk/Stainless-Steel-Braid-Radiat...laugh

Edited by SILICONE KID on Friday 15th October 19:05

SILICONE KID

Original Poster:

14,997 posts

262 months

Friday 15th October 2010
quotequote all
The s/steal braid fits perfect on both pipes .not like some ive seen.laughAny thoughts on the TVR POWER thermal insulator.i have no after pics because it`s not finishedlick

Edited by SILICONE KID on Friday 15th October 19:13

Pupp

13,038 posts

303 months

Friday 15th October 2010
quotequote all
SILICONE KID said:
The s/steal braid fits perfect on both pipes .not like some ive seen.laughAny thoughts on the TVR POWER thermal insulator.i have no after pics because it`s not finishedlick

Edited by SILICONE KID on Friday 15th October 19:13
The 'fabric' insulator works well; just as well as the rigid type, the material is pretty techie and highly insulative.

SILICONE KID

Original Poster:

14,997 posts

262 months

Friday 15th October 2010
quotequote all
Did you fit it dry or apply plenty of siliconelaugh

Pupp

13,038 posts

303 months

Friday 15th October 2010
quotequote all
SILICONE KID said:
Did you fit it dry or apply plenty of siliconelaugh
What do you think? Oh, oops, I see the problem...

SILICONE KID

Original Poster:

14,997 posts

262 months

Friday 15th October 2010
quotequote all
Well the instructions say dry but i feel at home armed with the silicone gunlaugh

spend

12,581 posts

282 months

Saturday 16th October 2010
quotequote all
Grind the rocket cover so that the rubber gasket lip fits it nicely. Most of the cast covers seem to have very poor tolerance of thickness around the corners & one long edge.

You can glue the rubber gasket to the cover, most use a few dabs of evostick (ie thin contact adhesive not a filler) but this is really because you are fitting the things upside down (gravity is not on your side). Alternatively studs make dry assembly (vaseline surfaces still - a little lube ensures they don't gall when tightening down) a much easier procedure, just acquire long nuts.