Powerflex diff bushes, fitting?
Powerflex diff bushes, fitting?
Author
Discussion

haircutmike

Original Poster:

22,511 posts

235 months

Saturday 16th October 2010
quotequote all
It may sound like a silly question, but...

When I fitted my suspension Superflex bushes, they came in 2 halves, a doddle to fit.

These Powerflex ones are one piece.

What's the best/easiest way to fit them?

Alexdaredevilz

5,697 posts

210 months

Saturday 16th October 2010
quotequote all
Lube,

or long bolt with large washers each end and do bolt up till bush is in, that make sense?

spend

12,581 posts

282 months

Saturday 16th October 2010
quotequote all
Grease them and press in using a vice.

haircutmike

Original Poster:

22,511 posts

235 months

Saturday 16th October 2010
quotequote all
Thanks guys, brains still a bit mushy from a good night out yesterday!

TVR Beaver

2,874 posts

211 months

Saturday 16th October 2010
quotequote all
Are they the best fix on the Diff... I did hear that they transfer a lot on noise and the rubber ones are best keeping in this application??

haircutmike

Original Poster:

22,511 posts

235 months

Saturday 16th October 2010
quotequote all
TVR Beaver said:
Are they the best fix on the Diff... I did hear that they transfer a lot on noise and the rubber ones are best keeping in this application??
Opinions please before I squeeze them in.


Alexdaredevilz

5,697 posts

210 months

Saturday 16th October 2010
quotequote all
haircutmike said:
TVR Beaver said:
Are they the best fix on the Diff... I did hear that they transfer a lot on noise and the rubber ones are best keeping in this application??
Opinions please before I squeeze them in.
If they split, your better upgrading them end of..........

As for noise, did you buy a Rolls Royce?

chimaera1855

334 posts

199 months

Saturday 16th October 2010
quotequote all
was wondering how much difference does it make to the ride and handling???

TJC46

2,199 posts

237 months

Saturday 16th October 2010
quotequote all
Once you go thru all the trouble of getting the rubber ones out, you would never in your wildest dreams try and insert similar back in. Poly bushes are easy to fit/remove compared to standard rubber ones, and if there durability is in doubt[which i disagree with] its quick and easy to put new ones in again. no brainer to me!

roysum

961 posts

220 months

Saturday 16th October 2010
quotequote all
TJC46 said:
Once you go thru all the trouble of getting the rubber ones out, you would never in your wildest dreams try and insert similar back in. Poly bushes are easy to fit/remove compared to standard rubber ones, and if there durability is in doubt[which i disagree with] its quick and easy to put new ones in again. no brainer to me!
Absolutely ! and no noise issues Peter.

Roy.

ps, you probably will not get a vice in to do the rear diff bush laugh but some threaded rod or a long bolt to pull it in works ok. Have fun !
Where did you go for the recon ??

haircutmike

Original Poster:

22,511 posts

235 months

Saturday 16th October 2010
quotequote all
chimaera1855 said:
was wondering how much difference does it make to the ride and handling???
Changed my suspension bushes for Superflex and changed the original dampers to Pro-Tech at the same time.

"Transformed" is the well used word and it is.

About to upgrade the dampers again to a "monotube" variety.

Roll on the delivery of my diff and P/S rack that didn't come yesterday banghead so I can get back on the road!

TVR Beaver

2,874 posts

211 months

Saturday 16th October 2010
quotequote all
Alexdaredevilz said:
haircutmike said:
TVR Beaver said:
Are they the best fix on the Diff... I did hear that they transfer a lot on noise and the rubber ones are best keeping in this application??
Opinions please before I squeeze them in.
If they split, your better upgrading them end of..........

As for noise, did you buy a Rolls Royce?
May be 'Noise' is the wrong word.... I think they ment more vibration type transfer from the non-rubber units... And the durabuility is not in question at all... I intend to do mine this winter with Powerflex... but was wondering about the diff... But also fair comment... if / when you get the old ones out.. I'm sure you won't want to put new rubber ones back... laugh
Is this operation best done with the diff out?

roysum

961 posts

220 months

Saturday 16th October 2010
quotequote all
TVR Beaver said:
Alexdaredevilz said:
haircutmike said:
TVR Beaver said:
Are they the best fix on the Diff... I did hear that they transfer a lot on noise and the rubber ones are best keeping in this application??
Opinions please before I squeeze them in.
If they split, your better upgrading them end of..........

As for noise, did you buy a Rolls Royce?
May be 'Noise' is the wrong word.... I think they ment more vibration type transfer from the non-rubber units... And the durabuility is not in question at all... I intend to do mine this winter with Powerflex... but was wondering about the diff... But also fair comment... if / when you get the old ones out.. I'm sure you won't want to put new rubber ones back... laugh
Is this operation best done with the diff out?
No, it's best done with the chassis out !
Seriously, take the diff out if you want any chance of doing it successfully. IMO of course.

spend

12,581 posts

282 months

Saturday 16th October 2010
quotequote all
It's certainly a lot easier with the diff out, but even then it's still awkward to get at the upper rear, side ones easy peasy taking a bracket out at a time.. wink

Poly bushes are great for the diff, the only criticism I know of is that the early cars have nothing to restrain the bush material as they float on the bearing and if that isn't glued to the bush material it well floats fore/aft.. I think Ant came up with a solution, but TBH the side brackets come out so bushes can be replaced pretty easily... Rear one always poly no doubt whatever the year hehe

haircutmike

Original Poster:

22,511 posts

235 months

Saturday 16th October 2010
quotequote all
So what's the easiest way to remove the rear rubber bush?

Alexdaredevilz

5,697 posts

210 months

Saturday 16th October 2010
quotequote all
haircutmike said:
So what's the easiest way to remove the rear rubber bush?
.

I got a air saw you can borrow

You could put blade right through cut sections out, and knock out with hammer,

Or there's FIRE!!!!!!!!


Edited by Alexdaredevilz on Saturday 16th October 22:12

haircutmike

Original Poster:

22,511 posts

235 months

Saturday 16th October 2010
quotequote all
The rear bush seems in perfect order and may have been renewed in the past.

Maybe it's me looking for a slightly easier life, (and I could do with that), is there any reason why it couldn't be left and just renew the other 2?

Oh, and why are we in on a Saturday evening asking and answering questions?

roysum

961 posts

220 months

Saturday 16th October 2010
quotequote all
haircutmike said:
The rear bush seems in perfect order and may have been renewed in the past.

Maybe it's me looking for a slightly easier life, (and I could do with that), is there any reason why it couldn't be left and just renew the other 2?

Oh, and why are we in on a Saturday evening asking and answering questions?
Funny that, I initially only replaced the "easy" two bushes but knew that I just had to rise to the challenge ! I have a Britool void bush tool. SVB1 which after a couple of attempts pulled her out. I did drill the rubber and remove the centre tube first.
If you are going to do it, start spraying the penetrating fluid now !
I'm quite happy to post the tool off to you. It makes squeezing the new one in eassier as well.

Roy.

Oh and it's due to us being sad old b------ds !!

haircutmike

Original Poster:

22,511 posts

235 months

Saturday 16th October 2010
quotequote all
Thanks Roy, will PM you.

spend

12,581 posts

282 months

Saturday 16th October 2010
quotequote all
roysum said:
Funny that, I initially only replaced the "easy" two bushes but knew that I just had to rise to the challenge ! I have a Britool void bush tool. SVB1 which after a couple of attempts pulled her out. I did drill the rubber and remove the centre tube first.
If you are going to do it, start spraying the penetrating fluid now !
I'm quite happy to post the tool off to you. It makes squeezing the new one in eassier as well.

Roy.

Oh and it's due to us being sad old b------ds !!
Freud (even old Clemmie) would have a field day with that post rofl

Excited about getting your hands on his tool eh Mike? hehe

I can't believe what folks do in public these days, I thought we were the most brazen in days of loon pants & tank tops scratchchin