changing dash early to late
Discussion
Hi guys high on my todo list is to change the dash to a leven stainless one. My car has the early type dash and i would like to fit the later one [with mods]which i think is a lot tidier. To keep the electrics simple i want to retain the 3 no buttons for the lights [i beleive the later single switch is connected via a ribbon cable to a light control box, and that sounds complicated to me] I was thinking of using this type which are backlit [ see pic below] so that removes the light i.d panel below the 3 buttons. I want to use the same for the hazard light switch also. I hope this is making sense. To the left of the radio is the now new backlit hazard switch, to the right is now the 3 no backlit switches for the side/headlights and rear fog.I would have to fit 4 no tiny warning lights elsewhere on the dash to replace the warning light cluster which is normally above the 3 buttons.
What do you think, is it worth it or should i just replace with a suitable early type stainless dash.Opinions, comments, welcome thanks Tom.
What do you think, is it worth it or should i just replace with a suitable early type stainless dash.Opinions, comments, welcome thanks Tom.To be honest that sounds like possibly a lot of work for very little gain, if your a competent auto electrician then go for it, if you only dabble and arent 100% comfortable id leave well alone. i took my lower dash out when i changed to stainless and thought it looked like multi coloured spaghetti behind there. so i just put the bits where they should go in the new one and screwed it back in place
Edited by lesstatt on Sunday 17th October 18:46
TJC46]Hi guys high on my todo list is to change the dash to a leven stainless one. My car has the early type dash and i would like to fit the later one [with mods said:
which i think is a lot tidier. To keep the electrics simple i want to retain the 3 no buttons for the lights [i beleive the later single switch is connected via a ribbon cable to a light control box, and that sounds complicated to me] I was thinking of using this type which are backlit [ see pic below] so that removes the light i.d panel below the 3 buttons. I want to use the same for the hazard light switch also. I hope this is making sense. To the left of the radio is the now new backlit hazard switch, to the right is now the 3 no backlit switches for the side/headlights and rear fog.I would have to fit 4 no tiny warning lights elsewhere on the dash to replace the warning light cluster which is normally above the 3 buttons.
What do you think, is it worth it or should i just replace with a suitable early type stainless dash.Opinions, comments, welcome thanks Tom.
I'd be interested seeing the switch you've used for the hazard warning light. I have the same dash as you and I've just chnaged the wood for a carbon effect. I looked everywhere for suitable switches and lights and in the end I've kept the originals.
What do you think, is it worth it or should i just replace with a suitable early type stainless dash.Opinions, comments, welcome thanks Tom.This is what mine looks like now ish..... (not finished yet)

floyd12345 said:
Thanks for that. Did you purchase an aftermarket dash or did you make your own? Would have a go myself at making one[access thru work to sheetmetal materials and tools,] just a bit concerned about getting it looking right on the heater controls. All the other cuts/openings are hid by the bezel on the dials and switches etc. so no problems with them. How easy is it to make your own with carbon fibre? Is this difficult to cut neatly?miniman said:
TJC46 said:
How easy is it to make your own with carbon fibre? Is this difficult to cut neatly?
I may be wrong but I suspect it's not carbon fibre, it's the original dash with carbon fibre effect sticky back plastic (for want of a better term) applied. I am considering replacing my veneer (which has got some cracks) and replace with an 'ebony' black look...
I do not want to go down the carbon or the stainless steel look but I want to update the buttons as well.
Haven't go a clue how I will do this yet, but it has been added to the Winter jobs list as a 'possible'...
Nosh
I do not want to go down the carbon or the stainless steel look but I want to update the buttons as well.
Haven't go a clue how I will do this yet, but it has been added to the Winter jobs list as a 'possible'...
Nosh
Gassing Station | Chimaera | Top of Page | What's New | My Stuff



