Picked a fight with a Gsxr 1000, and didn't go to plan
Picked a fight with a Gsxr 1000, and didn't go to plan
Author
Discussion

Alexdaredevilz

Original Poster:

5,697 posts

210 months

Tuesday 19th October 2010
quotequote all
So I managed to pick a fight with a super bike, after we had a little play, We stopped at a set of lights, only to see smoke pouring from my Chim, turned engine off ran out, only to find smoke pouring
from my glowing red hot brakes and small flames coming from the backs,

So im needing to upgrade my brakes, what's the best and cheapest way to do this?

I was thinking picking up some callipers off some thing else, e.g porsche 944 as i know there 4 pot brembo's modding them to fit, with some bigger discs vented and drilled, and new pads,

Or am I over thinking this and just need decent pads and discs?

Also do the 500 Chim/Griff use different system?

And before any ones says but this and that, bear in mind I got about £200-300 to play with, but im very handy with a spanner

Alex


Edit there standard 400 chim brakes with freodo pads, fitted by previous owner


Edited by Alexdaredevilz on Tuesday 19th October 16:48

4Lmike

1,910 posts

201 months

Tuesday 19th October 2010
quotequote all
the only thing i will say is....'you picked a fight with a gsxr 1000!!' silly boy

Alexdaredevilz

Original Poster:

5,697 posts

210 months

Tuesday 19th October 2010
quotequote all
4Lmike said:
the only thing i will say is....'you picked a fight with a gsxr 1000!!' silly boy
I was doing fine on the corners with him no problem

_DeeJay_

5,057 posts

285 months

Tuesday 19th October 2010
quotequote all
Alexdaredevilz said:
4Lmike said:
the only thing i will say is....'you picked a fight with a gsxr 1000!!' silly boy
I was doing fine on the corners with him no problem
Erm, yeah. Do you see those thick rubber things which were between you and the floor? Now compare those against the much smaller, and fewer in quantity rubber things that his bike was sat on.

Lets just hope you were lapping roundabouts any straights would get very embarrassing, very quickly.

dbv8

8,676 posts

251 months

Tuesday 19th October 2010
quotequote all
I say good on ya.
Bikes or should i say most riders are rubbish round corners. tongue out

Chimpaholic

9,637 posts

210 months

Tuesday 19th October 2010
quotequote all
£100 OVER BUDGET PLUS A SET A PADS - BUT STILL A BARGAIN.

http://cgi.ebay.co.uk/4-Pot-Caliper-Race-Brake-Kit...

THAT'S DEFINITELY WHAT I WOULD FIT.

dbv8

8,676 posts

251 months

Tuesday 19th October 2010
quotequote all
Chimpaholic said:
£100 OVER BUDGET PLUS A SET A PADS - BUT STILL A BARGAIN.

http://cgi.ebay.co.uk/4-Pot-Caliper-Race-Brake-Kit...

THAT'S DEFINITELY WHAT I WOULD FIT.
As supplied by 'Keri'
add VAT, pads and you need the hoses as the threads are slightly different = near £550.

Alexdaredevilz

Original Poster:

5,697 posts

210 months

Tuesday 19th October 2010
quotequote all
_DeeJay_ said:
Alexdaredevilz said:
4Lmike said:
the only thing i will say is....'you picked a fight with a gsxr 1000!!' silly boy
I was doing fine on the corners with him no problem
Erm, yeah. Do you see those thick rubber things which were between you and the floor? Now compare those against the much smaller, and fewer in quantity rubber things that his bike was sat on.

Lets just hope you were lapping roundabouts any straights would get very embarrassing, very quickly.
Yes thanks, Im not stupid and my last bike was a 996s, so I know about grip levels and bhp per ton, and how much I got raped on straights

It was just abit of fun

That ebay kit is nice, but I just don't have that much to spend right now, after 3 months of buying bits and bobs im running out of money, but at least the list is down to 6 things now, ITS ALMOST DONE!!

Alex

dbv8

8,676 posts

251 months

Tuesday 19th October 2010
quotequote all
and why do people think it would be 'very embarassing' to get blown away by a decent bike.
I think its brilliant.
Its much better when you see the reaction on the biker as he looks in his mirror and double takes as you are far closer than he expected laugh

.Mark

11,104 posts

307 months

Tuesday 19th October 2010
quotequote all
I gave up chasing/playing with bikes ages ago.





Well, until I got the Cerbera - Game on again! biggrin

Barreti

6,689 posts

268 months

Tuesday 19th October 2010
quotequote all
Find either some brakes off a later 500 car or the Ford units with 887/888 stamped on them (search on here for more info than I'll ever remember)

Get a pair of EBC GD150 front rotors and EBC Red Stuff pads.

Swap the rubber brake lines for braided

Use DOT4 fluid

I swapped all that on my 4.3 and the change was staggering. I can stand the car on its nose without any drama and the balance is still fine.

Be aware though, this improvement still cost me £30pa on my insurance premium because its a modification confused

peaktorque

1,807 posts

242 months

Tuesday 19th October 2010
quotequote all
^^^^^^^^^^^ yes ^^^^^^^^^^^^^^

I've obtained some of these from a 4x4 Cosworth (stamped 888/887), from ebay for about £50.

They are massive in comparison to the standard calipers.

I haven't fitted them yet as I need a new brake fluid resevoir rolleyes

Have a look here

Alexdaredevilz

Original Poster:

5,697 posts

210 months

Tuesday 19th October 2010
quotequote all
Brilliant info there guys thanks alot,

But im abit confused to the size of the disc, as the link show it done with 283mm, post above says 260mm
and ebc direct website is saying 278mm,

Will they all fit the 887/888 callipers? also what cars can i find these callipers? granada? sierra? escort? also what years/mk shall i search for?

Also what's to be done with the rears? or is it same again 887/888 with 260/278/283 discs?

Many thanks

Alex

Edit ive just seen a 273mm ford style aswell

Edited by Alexdaredevilz on Tuesday 19th October 20:44

peaktorque

1,807 posts

242 months

Tuesday 19th October 2010
quotequote all
I've got the 283mm disks, RS500 I believe. They will fit the 888/887 caliper (with a bit of help wink )

260mm is 500 Griff/Chim territory.....

I haven't bothered with the rears yet, but will probably go vented (as per later Chims), Cosworth sourced again probably.

SILICONE KID

14,997 posts

262 months

Tuesday 19th October 2010
quotequote all
I have the cosworth upgrade 887 888,purchased as a kit from Handal.The rear hubs need to be swopped for 2 wheel drive rear sierra cosworth hubs.I got mine for 40pounds plus new bearings.Im over the moon with my set up but some people say there to heavy.

Barkychoc

7,848 posts

235 months

Tuesday 19th October 2010
quotequote all
887 888 calipers I believe are also on Mondeo V6, not sure what vintage.

Andy_mr2sc

1,236 posts

207 months

Tuesday 19th October 2010
quotequote all
887/888 calipers are from mk1 mondeo early '90s. Not sure what else though I believe escort cossie. Discs are 283 or 285mm depending what you read and from a 3dr cossie or RS500 as someone above said. You may need 2mm washers between the caliper and carrier as I did to get the caliper central on the disc. DS2500 pads are the (bloody expensive!) way ahead. If the budget is that tight then original hoses match straight up.

Andy.

SILICONE KID

14,997 posts

262 months

Tuesday 19th October 2010
quotequote all
How do you get the 283mm discs to fit (front).The disc is very close to the edge of the calliper .For future reference what are the part numbers for discs and pads.


Sparky99

87 posts

201 months

Tuesday 19th October 2010
quotequote all
Just a though. if heat is the problem why not have some ducting to direct cool air onto the discs. Its a standard thing on many performance cars. Could be a cheap mod. Just a bit of chopping here and there!!

Alexdaredevilz

Original Poster:

5,697 posts

210 months

Tuesday 19th October 2010
quotequote all
Sparky99 said:
Just a though. if heat is the problem why not have some ducting to direct cool air onto the discs. Its a standard thing on many performance cars. Could be a cheap mod. Just a bit of chopping here and there!!
I was thinking about removing the front indicator and having some sort of ducting to the brakes, but haven't really looked in to it yet just a idea