started winter jobs
started winter jobs
Author
Discussion

andy450

Original Poster:

145 posts

197 months

Thursday 21st October 2010
quotequote all
started on the jobs to do list tonight,,,removed coolant hoses,rad,swan neck,thermostat,temp sender,,ready to fit all new parts from act ordered today.smile
anyone know the torque settings for thermostat housing ?
thanks


Edited by andy450 on Friday 22 October 18:01

Alexdaredevilz

5,697 posts

210 months

Thursday 21st October 2010
quotequote all
I managed to add to my to do list by cooking my brakes

andy450

Original Poster:

145 posts

197 months

Thursday 21st October 2010
quotequote all
havent got the brakes on my to do list (YET). . .brakes are good . . but that said was only going to change hoses this week and ended refreshing the whole lot !! ended up taking rad out as bottom hose clip was solid, that then exposed a broken rad mount bobbin and 12 years of road filth in front pan,so while rads out will clean and freshen up front earting point . . . which has led to the idea that the induction hose would be easier to change for a smooth bore act one while the rads out !!!
so when i get to the rebushing the suspension and painting/powder coating it may highlight a need for a brake change while its apart. . . list will end up growing with "while im there i may as well" IM SURE...
smilesmile

madasafrog666

210 posts

199 months

Thursday 21st October 2010
quotequote all
Winter is fun, dont keep them in the garage get them out for some exercise on dry sunny day when then council have not put too much salt on the roads.........Get the top off nothing better than a cold blast of air !!! wink

andy450

Original Poster:

145 posts

197 months

Friday 22nd October 2010
quotequote all
in a roundabout way taking it out for a cold blast of air on wednesday night is what led to the cooling system check over and the resulting OTT strip down earlier than planned.......got it out of garage,warmed it up on driveway then went for a drive out and the temp droped away and was strugling to stay hot when car was 30mph+..........so its now stripped and waiting on the new bits to arrive ! ! stat isnt stuck open but does seem to open fully early (around 70degs+/-) when checked ....its an 82deg stat.....the other worthwile finding was that the temp sender adapter was silted up around sensor and partialy blocked, all cleaned out and ready for new sender,will see if this helps with the gauge readings(but i doubt itsmile gauge readings aside it was the heater temp dropping that confirmed it was running cool.
anyhow enough of my rambling,off to work and await dhl delivery !

Edited by andy450 on Friday 22 October 07:53


Edited by andy450 on Friday 22 October 07:55

Simon BB

284 posts

246 months

Friday 22nd October 2010
quotequote all
Hi, I was told by a learned RV8 'expert' that the 'warming it up on the driveway' routine is a cam killer! Lobes lubricated by splash etc. was advised to fire her up and just go....

Sorry, off topic, I'll get my coat.....

Si

andy450

Original Poster:

145 posts

197 months

Friday 22nd October 2010
quotequote all
yea have had the same ideas myself on warming/not warming,,,,i am of the opinion that with my chim i start it move it out the garage and let it idle while shutting garage get back in and wait for the temp to get to 50ish so i know its not stone cold from the off ,, then drive for a few miles to get oil temp up and water temp normal before loading engine past 3k, its served me well over the years with my other performance/16v/turbo/Vs cars and touch me wood havent had a major faliure so far (feck me is that tempting fate or what) ive always used top quality oil and changed it always at 3k miles, or 6 mnths whichevers sooner !!
would be interesting to get other opinions from the well schooled on here on subject (rather than the "could someone explain the blatently obvious to me" threads of late smile )

ps back to my 1st post , stat kit from RG turned up today (excellelent service by the way) and it appears my over cooling probs are the orig stat IS opening to early (due to weakened spring id guess) compared to the new one .
so back into the garage over the weekend to put it all back together with the new hoses and ss swan neck from act (which also arrived today and was only ordered yesterday pm again excellent service totaly recomend both RG and ACT top service by both !!)


andy450

Original Poster:

145 posts

197 months

Saturday 30th October 2010
quotequote all


act hoses,stainless swan neck,new stat,otter switch,temp sender,magnecore leads,plug extenders,dizzy cap,lucas rotor arm,plugs,act smooth bore elbow and a bit of cleaning up ! back hurts and me wallets hurting a bit moe !! smile opinions please

Edited by andy450 on Saturday 30th October 17:35


Edited by andy450 on Saturday 30th October 17:36

Golflion

2,782 posts

252 months

Saturday 30th October 2010
quotequote all
andy450 said:


act hoses,stainless swan neck,new stat,otter switch,temp sender,magnecore leads,plug extenders,dizzy cap,lucas rotor arm,plugs,act smooth bore elbow and a bit of cleaning up ! back hurts and me wallets hurting a bit moe !! smile opinions please

Edited by andy450 on Saturday 30th October 17:35


Edited by andy450 on Saturday 30th October 17:36
Im just messing

Andy
If you're not changing the old ribbed pipe get some of this over it.

http://www.wickes.co.uk/Aluminium-Ducting/invt/713...