Golf Mk3 not starting, no fuel - ECU problem?
Golf Mk3 not starting, no fuel - ECU problem?
Author
Discussion

ProDave

Original Poster:

4 posts

193 months

Sunday 24th October 2010
quotequote all
1992 Mkiii Golf 1.8GL petrol (one of the very first mk3's)

The car died 2 days ago, initial symptoms loss of power, but would idle roughly. Now it won't start at all.

All plugs sparking, but all bone dry, no smell of fuel in the pistons.

I haven't done a compression check but no loss of oil or coolant, not overheated, and no emulsified oil, so I doubt that is the problem.

I've got the top off the carb body, it's the single point fuel injection version.

Fuel is getting to the carb, so fuel pump okay.

Fuel injector measures 1.4 ohms between it's two pins, so is within spec.

If I measure on the two pins going to the fuel injector, nothing at all. I've tried with a volt meter, and also tried my oscilloscope, in case I'm looking for pulses, but nothing.

So I suspect ECU or a wiring harness problem.

So the first question, where is the ECU located on this car? The Haynes manual tells you nothing other than take the car to a VAG dealer.

Edited by ProDave on Sunday 24th October 15:11

aka_kerrly

12,506 posts

241 months

Monday 25th October 2010
quotequote all
ECU is likely to be on the drivers side under the rain tray in the engine bay.
Have you checked the ECU RELAY is functioning , it is on the main fusebox under the dash. These arent that expensive at all and have been known to lead to the problems you are describing.

Does the fuel pump prime normally and the dash lights all light up as per normal when you turn the key? the other item that could be causing problems is the ignition switch.


dave

ProDave

Original Poster:

4 posts

193 months

Monday 25th October 2010
quotequote all
I've located the ECU now, under the scuttle cover under the windscreen.

The fuel pump does run for a few seconds when you turn the key, and fuel is definitely getting to the throttle body.

I've done some measurements with an ohm meter, and I get no continuity from the pins on the injector pump to any of the pins on the ECU connector.

I've located on the net several ECU wiring diagrams, but none that exactly match my car. Most show a fuse in line between the ECU and the injector. I have checked ALL the fuses in the fuse box and all are okay, so I wonder what sneaky hidden place the injector fuse may be?

Re the ECU relay, there is a position in the relay box labelled (according to the Haynes manual) for an ECU relay, but none is fitted. In fact only half the available relay positions are occupied. So if there is an ECU relay I don't know which one it is.

aka_kerrly

12,506 posts

241 months

Monday 25th October 2010
quotequote all
so the fuel pump primes and runs briefly then stops and there is definately spark? My understanding is that the coil sends a message to the ECU that the engine is firing and to continue running the fuel pump, if the ECU doesnt receive this signal it will not allow the fuel pump to keep running so this might be worth exploring. As would the crank position sensor, if this isnt sending a signal this to would prevent the engine from running.

Since the SPI engine has a VAGCOM port it would definately be worth getting the ECU read, this will allow you to determine if it is functioning and if there are any saved error codes which would highlight which sensor(s) are causing the issue and save a lot of time.

A very wild guess is an immobaliser fault as this to would prevent the car running but allow the fuel pump to prime just not continue running. I havent come across many that fail over time giving poor running as you described they tend to just die outright.

Dave

aka_kerrly

12,506 posts

241 months

Monday 25th October 2010
quotequote all
just to add.

It seems it is the MPI unit that has a ECU relay NOT the SPI.

Another suggestion is to make sure the throttle body intake is on and not split. It's just a i recall a mates 1.4SPI dying and not running and it was because the intake pipe was split letting far too much unmetered air into the system and thus leaning the fuel mix so much the engine wouldnt run.

The final thing i can think of right now is if you can get a test light and put it on the injectors one at a time when the engine is cranked, injectors should have 12v on 1 terminal, nothing on the other terminal. If you have nothing, check the wiring block on the ECU.

I am out of ideas now :-(

dave

ProDave

Original Poster:

4 posts

193 months

Monday 25th October 2010
quotequote all
All fixed.

I started tracing the wiring through the harness, and found a broken wire where the harness plugs into the throttle body, stopping the 12V getting to the injector.

Thanks for all the help.