Tiny grub screw
Tiny grub screw
Author
Discussion

SILICONE KID

Original Poster:

14,997 posts

262 months

Wednesday 27th October 2010
quotequote all
Can any one tell me what the tiny grub screw on the plenum hidden under the throttle mechanism does ..

v8 racing

2,064 posts

282 months

Wednesday 27th October 2010
quotequote all
Quinny said:
Don't touch it....

It holds the laffing shaft onto the gigling pin.....if you mess with it the flunkum valve will drop out...
took the words out my mouth..

Chimpafrolic

9,637 posts

210 months

Wednesday 27th October 2010
quotequote all
Quinny,

Sorry to correct you but i think you will find the Flukum valve is held by the gigling pin not the other way round as you have indicated.

Easy mistake to make.

Rotating the grub screw 90 degrees releases the flangy trunnion which is useful for modulating the wimwam override bleed circuit.

roysum

961 posts

220 months

Wednesday 27th October 2010
quotequote all
Grubscrew..........lunch time scensoredg

SILICONE KID

Original Poster:

14,997 posts

262 months

Wednesday 27th October 2010
quotequote all
What are you all talking about?does it do anything?.It goes well just want it to tick over so i can drive it over .I can`t adjust the accelerator cable any more and moveing the TPS makes no difference.The thermal insulator may of changed a
few things..Just running to slow.If i lift the throttle slightly it ticks over spot on .

Edited by SILICONE KID on Wednesday 27th October 22:52

Alexdaredevilz

5,697 posts

210 months

Wednesday 27th October 2010
quotequote all
Chimpafrolic said:
Quinny,

Sorry to correct you but i think you will find the Flukum valve is held by the gigling pin not the other way round as you have indicated.

Easy mistake to make.

Rotating the grub screw 90 degrees releases the flangy trunnion which is useful for modulating the wimwam override bleed circuit.
What about if you throw a double 6 on the scrabble board using your left hand? or does that affect the warp speed of the flux capacitor?

Chimpafrolic

9,637 posts

210 months

Wednesday 27th October 2010
quotequote all
SILICONE KID said:
What are you all talking about?does it do anything?.It goes well just want it to tick over so i can drive it over .I can`t adjust the accelerator cable any more and moveing the TPS makes no difference.The thermal insulator may of changed a
few things..Just running to slow.If i lift the throttle slightly it ticks over spot on .

Edited by SILICONE KID on Wednesday 27th October 22:52
I found the Mark Adams chip solved my idle problems.

Do you want to buy mine Daz?

£400.00 to you.

SILICONE KID

Original Poster:

14,997 posts

262 months

Wednesday 27th October 2010
quotequote all
Moved on from that rubbish!chips and Dizzys old hatlaughThanks for your Cooperation,furiousI sold mine for a reasonable price,thats why i am a gentleman...hurl

Edited by SILICONE KID on Wednesday 27th October 23:42

spend

12,581 posts

282 months

Thursday 28th October 2010
quotequote all
It sets the throttle stop to set the butterfly when closed, the stops on the brackets do similar for fully open (and can occasionally prevent full throttle BTW).

Base idle is the bigger socket set screw from the top, but you've probably powder coated the whole shebang up nice and solid????

Meatball

1,638 posts

241 months

Thursday 28th October 2010
quotequote all
Re calibrate your TPS in your tunerstudios, under the tools menu,
Save your settings before you start. hehe

SILICONE KID

Original Poster:

14,997 posts

262 months

Thursday 28th October 2010
quotequote all
I can`t find a Allen key to fit ,is it imperial..
Do you know anything about this
I've been informed, better mileage is possible from MAP based tuning (Speed-density) rather than RPM based (Alpha-N).

RPM based is often used by tuners as it's easier to tune, compared to MAP, but if you can get MAP right then it should be better. I don't yet know what the difference would really be in terms of MPG, but I have got mine set-up for MAP based, so once its ina decent state of tune I can report back and will be interesting to compare figures. I suspect you are running an RPM based map - which is the way to go if you have a really knobbly cam (which again I suspect you do?)

Edited by SILICONE KID on Thursday 28th October 19:10

Ant.

5,254 posts

312 months

Thursday 28th October 2010
quotequote all
Daz, it is nearly November.


Put the fking Chimpy thing in the garage and leave it alone !!!!!!!!

SILICONE KID

Original Poster:

14,997 posts

262 months

Thursday 28th October 2010
quotequote all
I have it on Axle Stands rubbing down the brush finish so i can spray itidea

spend

12,581 posts

282 months

Thursday 28th October 2010
quotequote all
Yes I guess, I certainly use an imperial one don't ask me what size though. I just take a spare plenum over to the tool rack & find the right one (but I do know its from the blue imperial collection) hehe

rigga

8,808 posts

232 months

Thursday 28th October 2010
quotequote all
Will there ever be a week when there is no post from Daz messing with his car that was SORTED by someone who knows what he is doing ?

You seem awefully obsessed with mpg for a 5ltr owner......