I was bored!
I was bored!
Author
Discussion

LordB

Original Poster:

461 posts

282 months

Friday 29th October 2010
quotequote all

Alexdaredevilz

5,697 posts

210 months

Friday 29th October 2010
quotequote all
nono

macdeb

8,760 posts

286 months

Friday 29th October 2010
quotequote all
Quinny said:
Did Stevie Wonder fit the 450 badge on the plenumnhehehehe
hehe

SILICONE KID

14,997 posts

262 months

Friday 29th October 2010
quotequote all
I removed the silver insulation from the smooth bore elbow,it does look better but it gets very hot.Does that not worry you,hot air is not a good idea.Im going to try again and do a better jobrolleyesI like the silver sleeve on the induction ,where did you get that from.



Edited by SILICONE KID on Friday 29th October 17:20

LordB

Original Poster:

461 posts

282 months

Friday 29th October 2010
quotequote all
Silver insulation is from Wicks! Its basically a 5" corrogated aluminium/tin foil duct (I think plumbers use it for air ducting stuff) I just sleeved it straight on - be careful its quite fragile.

I'm pretty sure I only paid a few pounds for it.....aside the stuff selling in the specialists it was a steel.

Golflion

2,782 posts

252 months

Friday 29th October 2010
quotequote all
Quinny said:
PLUMBERS USE ITyikesyikes

You've gone and done it nowhehehehe
Daz give us a wavebyebye

Not a bad idea though you must admit silico kidbow

Chimpafrolic

9,637 posts

210 months

Friday 29th October 2010
quotequote all
Oh no, here we go again whistle

I must resist, I must resist, I must resist, I must resist,I must resist, I must resist, I must resit, I must resist,I must resit, I must resist, I must resit, I must resist!

rolleyes

SILICONE KID

14,997 posts

262 months

Friday 29th October 2010
quotequote all
What about that smooth bore elbow,its red hot..Does it not make a difference..rolleyes
By the way im a Gas Safe heating engineer.Been in the trade since 1984 trained as a commercial pipe fitter and never touched plastic ducting..laughMy company is DC PLUMBING HEATING & GAS SERVICES.!

Edited by SILICONE KID on Friday 29th October 22:33

Alexdaredevilz

5,697 posts

210 months

Friday 29th October 2010
quotequote all
SILICONE KID said:
What about that smooth bore elbow,its red hot..Does it not make a difference..rolleyes
By the way im a Gas Safe heating engineer.been in the trade since 1984 and never touched plastic ducting..laugh
And there's me thinking gas safe only come into play April 2010

SILICONE KID

14,997 posts

262 months

Friday 29th October 2010
quotequote all
Yes Corgi before but Gas Safe could do it cheaper.

Alexdaredevilz

5,697 posts

210 months

Friday 29th October 2010
quotequote all
SILICONE KID said:
Yes Corgi before but Gas Safe could do it cheaper.
Im just messing

I think heres the stuff he's talking about from wickes (looks like im going there tomorrow my self)

http://www.wickes.co.uk/Aluminium-Ducting/invt/713...

pbaker43

268 posts

199 months

Saturday 30th October 2010
quotequote all
Before you guys get all technical about U bends, elbow joints, not to mention the rear connections (careful there)eek I was under the impression that the induction pipe need to be smooth to help the air flow and not to tumble, so using the Plumbers pipe will this not increase the induction problems confused?

Mr MoJo

4,698 posts

247 months

Saturday 30th October 2010
quotequote all
pbaker43, I think the ducting is slipped over the smooth bore pipe ??

It actually looks very neat, does is slip over easily, ie is it the correct diameter to cover the smooth bore pipe or does it need cutting ?

May be a trip to Wickes on the cards !!

pbaker43

268 posts

199 months

Saturday 30th October 2010
quotequote all
Thanks for telling me boxedin feel a prat for asking getmecoat

LordB

Original Poster:

461 posts

282 months

Saturday 30th October 2010
quotequote all
Mr MoJo said:
pbaker43, I think the ducting is slipped over the smooth bore pipe ??

It actually looks very neat, does is slip over easily, ie is it the correct diameter to cover the smooth bore pipe or does it need cutting ?

May be a trip to Wickes on the cards !!
No cutting and just slips straight over - be careful when putting the AFM back on - mods dont get much easier or cheaper than this. I had thought that I should wrap the indiction pipe before fitting the duct over the top....but I couldnt be arsed. There is a good air gap (bet duct and intake pipe)that should add some insulating value.

LordB

Original Poster:

461 posts

282 months

Saturday 30th October 2010
quotequote all
Alexdaredevilz said:
SILICONE KID said:
Yes Corgi before but Gas Safe could do it cheaper.
Im just messing

I think heres the stuff he's talking about from wickes (looks like im going there tomorrow my self)

http://www.wickes.co.uk/Aluminium-Ducting/invt/713...
clap