Wax Injected outriggers
Discussion
Would you guys recommend injecting the outriggers with wax?
I'm on the original ones that are OK but were very rusted when I got the car 3 years ago. Did a major refurb on them then & spayed every year since.
What I don't know is if there are any perferations in the top of the tubes.
I have two new cans of Dynax S50 so was thinking of drilling a couple of 10mm holes each side and using the injection wand before sealing with a tappered grommet.
What do you think?
I'm on the original ones that are OK but were very rusted when I got the car 3 years ago. Did a major refurb on them then & spayed every year since.
What I don't know is if there are any perferations in the top of the tubes.
I have two new cans of Dynax S50 so was thinking of drilling a couple of 10mm holes each side and using the injection wand before sealing with a tappered grommet.
What do you think?
Quinny said:
I wouldn't..
Sealed steel tube corrodes from the outside... The inside isn't exposed to air and moisture, so won't go rusty if the chassis has been welded correctly
The inside will only start to rust, once the tube become perforated .
If this happens because the tube has rusted from the outside, it's to late anyway...
By drilling, an otherwise sealed tube, you are introducing air, and therefore moisture, and starting the process ahead of time....
EFASealed steel tube corrodes from the outside... The inside isn't exposed to air and moisture, so won't go rusty if the chassis has been welded correctly
The inside will only start to rust, once the tube become perforated .
If this happens because the tube has rusted from the outside, it's to late anyway...
By drilling, an otherwise sealed tube, you are introducing air, and therefore moisture, and starting the process ahead of time....
From experience of all the chassis I have refurbished, 70 plus.....I NEED to find the original welders incomplete weld, these days I rely on the shot blasters to do this (I used to look my self) BUT, IF you shot blast a chassis and then rotate it, any missing weld will drip water where the damp air has condensed internally, that tube/joint/needs to assessed for internal rust and most likely replaced.
Adrian@
Adrian@
so Adrian@, you're saying not to rely on the welds to the chassis being airtight? When you find these bits missing, do you then get the welds completed? Does that make the chassis airtight? If not, then is there something to be gained from injecting the tubes as described? Or are the downsides of not being able to weld it in future outweighing the benefits of waxing the insides?
Just wondering - so far all the different views on this topic (over all the other threads on chassis treatment, not just this one) have me confused.
Just wondering - so far all the different views on this topic (over all the other threads on chassis treatment, not just this one) have me confused.
BenRelle said:
so Adrian@, you're saying not to rely on the welds to the chassis being airtight? When you find these bits missing, do you then get the welds completed? Does that make the chassis airtight? If not, then is there something to be gained from injecting the tubes as described? Or are the downsides of not being able to weld it in future outweighing the benefits of waxing the insides?
Just wondering - so far all the different views on this topic (over all the other threads on chassis treatment, not just this one) have me confused.
Critical is that the weld joint is airtight, welders at the factory were very good, but find that most chassis are missing the odd weld ...IF proof were needed on the oxygen feeding the rust then the missing welds and the rotted tube go hand in hand...I have a chassis in today, internally Waxoyl'ed grub screw'ed outriggers on a chassis that were replaced in 1999 are due to be replaced NOW.Just wondering - so far all the different views on this topic (over all the other threads on chassis treatment, not just this one) have me confused.
Adrian@
Worth noting is the second method of rot on TVR chassis..heat related rot from the exhaust manifolds, seen often on S through to Cerbera (prior to the moulded heat shielding models)
Edited by Adrian@ on Monday 1st November 10:58
I agree Adrian, the manifold rot always worries me more. It's an awful lot more work to replace/repair those elements of the chassis, I would always advocate ceramic coated manifolds personally.
I must admit I would consider not just painting any outrigger replacement if I had to have them done, but encapsulating all the weld joints with fibreglass?
I must admit I would consider not just painting any outrigger replacement if I had to have them done, but encapsulating all the weld joints with fibreglass?
An effective repair to the top rail is to open the tube end and knock a piece of machined tubed down having drilled around the repair with a 10mm drill and then puddle weld the holes and replace the end again......then stitch weld the rusty weak areas over with C9 welding rods prior to dressing back to the make the job invisible...IT helps that I TIG/MIG/Plasma weld on shot blasted chassis's and can rotate them BUT for outriggers where round tubes meet flat plate I ALWAYS fill the voids with bronze to stop the undercut being a riser for dirt and damp to start the process happening again.
Adrian@
Re the glass fibre...I use glass fibre resin to paint my alloy fuel tanks prior to fitting these days..for the out riggers it is not something that I had thought about....but the pre 68 TVR's with bonded on chassis that I have worked on fair very well IF the tubes are airtight.
Adrian@
Re the glass fibre...I use glass fibre resin to paint my alloy fuel tanks prior to fitting these days..for the out riggers it is not something that I had thought about....but the pre 68 TVR's with bonded on chassis that I have worked on fair very well IF the tubes are airtight.
Edited by Adrian@ on Monday 1st November 12:19
This is getting more complex than I first thought.
Although my tubes are strong I think there could well be a breach, if only tiny. I only run the car in the dry or almost dry. So damp days could well introduce moisture. If I can delay any internal rusting through injecting that seems a prudent measure to preseve the rails as long as possible.
So I think I will proceed?
Although my tubes are strong I think there could well be a breach, if only tiny. I only run the car in the dry or almost dry. So damp days could well introduce moisture. If I can delay any internal rusting through injecting that seems a prudent measure to preseve the rails as long as possible.
So I think I will proceed?
Gassing Station | Chimaera | Top of Page | What's New | My Stuff


