American tool for cam belt replacement?
American tool for cam belt replacement?
Author
Discussion

Jack_and_MLE

Original Poster:

626 posts

270 months

Friday 12th November 2010
quotequote all
Hi

Probably one for Tame Technician

I have been on the phone to the garage who did my cam belt before and after a change of ownership they are telling me my engine V6 TDI 2.5 2003 is a special engine and they need a special tool only available in the US to lock everything in place.

It sound like
1) they have broken something
2) don't want to admit it
3) or they don't want to do the work.

Do you need a special tool from the us to change a cambelt on a v6 tdi?
How can I check what they did?

Kind regards


Jack Morgan-Smith

Tame Technician

2,467 posts

235 months

Friday 12th November 2010
quotequote all
Just about every cam belt requires special tools.


There is not just one tool to do the 2.5TDI belt, there are about 5.

A crank locking tool
A pin to lock the injection pump
Two camshaft locking wedges
special socket to tighten the pump drive belt tensioner

you also need a special small puller to pop the top pulleys off.

The 2.5TDI engine isnt special its just a pain, a bit complicated.

Tools are available from any Audi centre or TPS, But you would need to know the numbers to order them, the parts dept cant look up a tool number from a description.

Or Sealey, Mac and Snap-on will have kits available.

http://www.google.co.uk/products?hl=en&safe=of...





Edited by Tame Technician on Friday 12th November 11:52

Tame Technician

2,467 posts

235 months

Friday 12th November 2010
quotequote all
OR to put it another way.

Imagine you a local indy garage who work on all makes of car.

You might have to buy all these tools, and use them once or twice.

http://www.justoffbase.co.uk/Tool-Shop?search=lock...


Jack_and_MLE

Original Poster:

626 posts

270 months

Friday 12th November 2010
quotequote all
Cheers Tame

This garage supposed to be VW Audi Specialist.

My main worry is that they could have damaged or undone something which could result in the catastrophic failure of the engine.

Is there any way I can check it?

Cheers

Jack

Tame Technician

2,467 posts

235 months

Friday 12th November 2010
quotequote all
Not sure I entirely understand the problem, they did the belt for you before, but now they say they cant because they dont have the tooling? So your worries they did it before without the correct tooling, is that it.??

You can fit belts without the tools, but you have to use crude methods like painted marks to line things up, this can result in a mistimed engine. But if performance is ok and they is no change in how the engine idles smokes etc between before and after the belt change, then there is nothing to worry about.


Jack_and_MLE

Original Poster:

626 posts

270 months

Friday 12th November 2010
quotequote all
"So your worries they did it before without the correct tooling, is that it"

My worries is how far down did they go before finding out they didn't have the right tooling to do the work.
Or if they have damaged something whiles trying to do the work.

Kind regards

Jack

Tame Technician

2,467 posts

235 months

Friday 12th November 2010
quotequote all
Oh i see

Its unlikely they would have damaged anything taking it apart, more a case of, they cant time it to put it back together without the tools.

Does sound a bit strainge though.

NBirkitt

252 posts

222 months

Monday 15th November 2010
quotequote all


A recent article in Audi Driver magazine (Sept 2010 issue) showed how this job can be done without special tools...