DIY Vinyl Wrap - Anyone tried it?
Discussion
I have seen a couple of posts on car forums of people who have had a go at wrapping their car with what appear to be good results, and if you look at some of the videos on youtube it doesn't look too tricky - but then I guess a pro will always make it look easy!
The basic material costs don't seem bad, so if you can save on the labour of having the job done and still end up with good results... Thinking of wrapping my BMW E91 in matt silver...
So have any PHers had a crack at wrapping their own cars? How did you get on - any pics or advice?

The basic material costs don't seem bad, so if you can save on the labour of having the job done and still end up with good results... Thinking of wrapping my BMW E91 in matt silver...
So have any PHers had a crack at wrapping their own cars? How did you get on - any pics or advice?

Its definitely a nack.
I've put graphics on my motocross bike several time, and that shield stuff what I had an Elise. Start on a piece that is flat and small as possible, and work up to the curves. I guarantee you'll have some air bubbles though.
Oh and make sure the body work is uber clean, and do inside a garage - not out in the wind as you'll get dust/whatever under it.
I've put graphics on my motocross bike several time, and that shield stuff what I had an Elise. Start on a piece that is flat and small as possible, and work up to the curves. I guarantee you'll have some air bubbles though.
Oh and make sure the body work is uber clean, and do inside a garage - not out in the wind as you'll get dust/whatever under it.
I've only applied mostly flat graphics and that is tricky enough.
Wrapping curves is a definite skill, even with the more flexible/stretchable stuff. It is certainly a multi-day job for a novice, do some reading and speak/email people who have done it DIY, and prepare to waste a fair bit of material.
Wrapping curves is a definite skill, even with the more flexible/stretchable stuff. It is certainly a multi-day job for a novice, do some reading and speak/email people who have done it DIY, and prepare to waste a fair bit of material.
I've tried wrapping some plastics from a motorbike.
Few things I figured out...
It's fookin hard
Get as many people as you can to help
Have a very sharp knife to hand
Have a decent hot air gun/hairdryer to hand
Buy a LOT more than you need, you will mess it up
Have a cloth wrapped squeegee to hand
I gave up after about 2 1/2 hours on the same panel. I was doing it on my own though so trying to stretch the wrap whilst posistioning it, heating it and squeeging it all at the same time was canny hard.
Few things I figured out...
It's fookin hard
Get as many people as you can to help
Have a very sharp knife to hand
Have a decent hot air gun/hairdryer to hand
Buy a LOT more than you need, you will mess it up
Have a cloth wrapped squeegee to hand
I gave up after about 2 1/2 hours on the same panel. I was doing it on my own though so trying to stretch the wrap whilst posistioning it, heating it and squeeging it all at the same time was canny hard.
hmmm , not so easy then. Maybe i'll experiment with some small pieces first to see how I get on and then take it from there if I feel confident enough.
I have looked at the 3M website and they do a car wrap vinyl that does not stick until squeegee'd so you can position it more easily and has small channels in it to aid air bubble removal. The hardest parts would be bumpers and finishing off round door frames etc...
http://solutions.3m.co.uk/wps/portal/3M/en_GB/Grap...
I have looked at the 3M website and they do a car wrap vinyl that does not stick until squeegee'd so you can position it more easily and has small channels in it to aid air bubble removal. The hardest parts would be bumpers and finishing off round door frames etc...
http://solutions.3m.co.uk/wps/portal/3M/en_GB/Grap...
JaySTee said:
hmmm , not so easy then. Maybe i'll experiment with some small pieces first to see how I get on and then take it from there if I feel confident enough.
I have looked at the 3M website and they do a car wrap vinyl that does not stick until squeegee'd so you can position it more easily and has small channels in it to aid air bubble removal. The hardest parts would be bumpers and finishing off round door frames etc...
http://solutions.3m.co.uk/wps/portal/3M/en_GB/Grap...
My dad has been putting "wraps" (solar film) on model aeroplanes for years, and what a job it is to get a perfect job on a small wing. Let alone a car. Best to let the professionals do it, who have the tooling, workshops, experience and team work. I think it is quite an art... especially if you want it to last 5 years.I have looked at the 3M website and they do a car wrap vinyl that does not stick until squeegee'd so you can position it more easily and has small channels in it to aid air bubble removal. The hardest parts would be bumpers and finishing off round door frames etc...
http://solutions.3m.co.uk/wps/portal/3M/en_GB/Grap...
JaySTee said:
So have any PHers had a crack at wrapping their own cars? How did you get on - any pics or advice?
Have you ever tried wallpapering, I have and find it nigh on impossible to get pre-cut rolls of paper to go on smooth and without bubbles on a flat straight wall, god knows how difficult it must be to do it on the curved panels of a car with lots of cutting involved.If you do decide to do it, post up some photos. Good luck!
stuart-b said:
JaySTee said:
hmmm , not so easy then. Maybe i'll experiment with some small pieces first to see how I get on and then take it from there if I feel confident enough.
I have looked at the 3M website and they do a car wrap vinyl that does not stick until squeegee'd so you can position it more easily and has small channels in it to aid air bubble removal. The hardest parts would be bumpers and finishing off round door frames etc...
http://solutions.3m.co.uk/wps/portal/3M/en_GB/Grap...
My dad has been putting "wraps" (solar film) on model aeroplanes for years, and what a job it is to get a perfect job on a small wing. Let alone a car. Best to let the professionals do it, who have the tooling, workshops, experience and team work. I think it is quite an art... especially if you want it to last 5 years.I have looked at the 3M website and they do a car wrap vinyl that does not stick until squeegee'd so you can position it more easily and has small channels in it to aid air bubble removal. The hardest parts would be bumpers and finishing off round door frames etc...
http://solutions.3m.co.uk/wps/portal/3M/en_GB/Grap...
I have limited wallpapering experience as I have only hung lining paper, but it looked ok

If I do give it a go it will not be until after Easter as the ambient temp and surface temp is important from what I have read and I do not have heating in my garage!
Edited by JaySTee on Tuesday 7th December 14:17
andyr30 said:
I've tried wrapping some plastics from a motorbike.
Few things I figured out...
It's fookin hard
Get as many people as you can to help
Have a very sharp knife to hand
Have a decent hot air gun/hairdryer to hand
Buy a LOT more than you need, you will mess it up
Have a cloth wrapped squeegee to hand
I gave up after about 2 1/2 hours on the same panel. I was doing it on my own though so trying to stretch the wrap whilst posistioning it, heating it and squeeging it all at the same time was canny hard.
I've put some on mine & agree it's very tricky to get it to lay on the surface without getting all the air bubbles out or distorting the edges if you mess around with it too much. Few things I figured out...
It's fookin hard
Get as many people as you can to help
Have a very sharp knife to hand
Have a decent hot air gun/hairdryer to hand
Buy a LOT more than you need, you will mess it up
Have a cloth wrapped squeegee to hand
I gave up after about 2 1/2 hours on the same panel. I was doing it on my own though so trying to stretch the wrap whilst posistioning it, heating it and squeeging it all at the same time was canny hard.
It's probably alot harder on a motorcycle as the tight radii' of vents & fairings in general make it very tricky. Worth spraying soapy water on before you apply the vinyl- it'll allow you to move it around without it sticking whilst applying.
Vidal Baboon said:
I've put some on mine & agree it's very tricky to get it to lay on the surface without getting all the air bubbles out or distorting the edges if you mess around with it too much.
It's probably alot harder on a motorcycle as the tight radii' of vents & fairings in general make it very tricky. Worth spraying soapy water on before you apply the vinyl- it'll allow you to move it around without it sticking whilst applying.
I have used soapy water when sticking boat names on and signs to windows etc and it works well but the 3M car vinyl you apply dry as apparnetly it does not stick until squeegee'd out...It's probably alot harder on a motorcycle as the tight radii' of vents & fairings in general make it very tricky. Worth spraying soapy water on before you apply the vinyl- it'll allow you to move it around without it sticking whilst applying.
ZesPak said:
isn't matt silver, like, grey?
it looks metalic silver but not shiney, not like grey or primer.chuno said:
Does anyone know how i can buy the 3M stuff in the link above??
I have not taken it any further so not sure. I would suggest trying to contact 3M in the UK from there website and ask them but they probably only sell to trade. There is some stuff on ebay so you could look there...I've not really looked into this much but how do you stop bubbles from forming in the wrap? Also, how would you do something with really tight complex curves like the headlight scoop on something like this:

Would that just be impossible? Just thinking about it now, the size of the sheet you'd need to do the bonnet would be ridiculous - I think I'd just respray it, it would be easier!

Would that just be impossible? Just thinking about it now, the size of the sheet you'd need to do the bonnet would be ridiculous - I think I'd just respray it, it would be easier!
Gassing Station | General Gassing | Top of Page | What's New | My Stuff




