VW Corrado, MAF cleaning
Discussion
Hi,
1) Have you had the car put on a diagnostic?
2) I'm assuming your problem is some kind of misfire. The MAF is a sealed unit. Before try to rip that apart do check:
a) That all the hoses between the airbox and the throttle are airtight and havn't split
b) That it's not a plug or HT lead.
c) Check that the connectors in the plug to the MAF havn't corroded (this is a problem I recently had - bit of contact cleaner sorted it)
I've run VR6s for years now and I don't think the MAF units are really designed to be "cleaned". Aside from blowing some air through it I don't think trying to clean it will actually fix a failing MAF. See if you can find one off a Golf in the scrappies or a mate and try swapping it out, but note there are a couple of different MAFs, with 4 pin connectors on earlier cars and a 5 pin on later cars.
If the problem isn't so much a misfire as a down on power problem, you need to extend your search to things like cam sensors and the engine loom as these will cause the ECU to drop into safe mode and give you a 140bhp VR6. At this point you should try and get the car on a diagnostic - helpfully a lot of mobile mechs carry a reader which will be a lot cheaper than taking it to Volkswagen.
HTH,
John
1) Have you had the car put on a diagnostic?
2) I'm assuming your problem is some kind of misfire. The MAF is a sealed unit. Before try to rip that apart do check:
a) That all the hoses between the airbox and the throttle are airtight and havn't split
b) That it's not a plug or HT lead.
c) Check that the connectors in the plug to the MAF havn't corroded (this is a problem I recently had - bit of contact cleaner sorted it)
I've run VR6s for years now and I don't think the MAF units are really designed to be "cleaned". Aside from blowing some air through it I don't think trying to clean it will actually fix a failing MAF. See if you can find one off a Golf in the scrappies or a mate and try swapping it out, but note there are a couple of different MAFs, with 4 pin connectors on earlier cars and a 5 pin on later cars.
If the problem isn't so much a misfire as a down on power problem, you need to extend your search to things like cam sensors and the engine loom as these will cause the ECU to drop into safe mode and give you a 140bhp VR6. At this point you should try and get the car on a diagnostic - helpfully a lot of mobile mechs carry a reader which will be a lot cheaper than taking it to Volkswagen.
HTH,
John
Edited by corozin on Wednesday 12th January 21:45
As corozin said, MAFs arean't really designed to be cleaned as once they stop functioning properly, they are not really repairable. Having said that, cleaning them can offer a temporary fix if you are certain that the MAF is at fault and have the time to clean it.
The best solution to clean the hot wire with is IPA (Isoproyl Alcohol). Remember, the hot wire is very brittle so if you touch it with your finger it may break or if you spray fluid on the wire it could possibly break too.
IPA can be found in your local Maplins store.
The best solution to clean the hot wire with is IPA (Isoproyl Alcohol). Remember, the hot wire is very brittle so if you touch it with your finger it may break or if you spray fluid on the wire it could possibly break too.
IPA can be found in your local Maplins store.
Robatr0n said:
As corozin said, MAFs arean't really designed to be cleaned as once they stop functioning properly, they are not really repairable. Having said that, cleaning them can offer a temporary fix if you are certain that the MAF is at fault and have the time to clean it.
The best solution to clean the hot wire with is IPA (Isoproyl Alcohol). Remember, the hot wire is very brittle so if you touch it with your finger it may break or if you spray fluid on the wire it could possibly break too.
IPA can be found in your local Maplins store.
No! You need electrical contact cleaner, not IPA. You can spray contact cleaner onto the filament, but in reality, the sensitivity is so great that it won't make that much difference, if at all. The best solution to clean the hot wire with is IPA (Isoproyl Alcohol). Remember, the hot wire is very brittle so if you touch it with your finger it may break or if you spray fluid on the wire it could possibly break too.
IPA can be found in your local Maplins store.
Wihtout knowing the exact nature of the problem, have you cleaned out the ISV (source of many idling/running problems on OBD1 cars) and changed the blue ECU temperature sensor?
I have some slight hesitation at part throttle on my VR6, but the MAF is that last thing I'll be replacing if it's neither the leads, Coilpack, plugs, nor just needing a decent oil change. I've cleaned the ISV, replaced the leads, the plugs are less than 5k miles old and the coilpack is 1 year old. If an oil change using the best oil I can find doesn't cure it, only then will I replace the MAF.
Admittedly it's a different car but when the MAF on my S2 started playing up, IPA was absolutely fine to use on it until I replaced it with the RS2 MAF.
As it happens, the hot wire can be very brittle and it's not uncommon for them to break if they are handled without care. Believe it or not, spraying a cleaner on the wire can easily break it.
As it happens, the hot wire can be very brittle and it's not uncommon for them to break if they are handled without care. Believe it or not, spraying a cleaner on the wire can easily break it.
Hi John,
Sorry, Had loads of other stuff on the go.
I usually post for the Corrado on the corrado forum, as, from experience there is a higher chance of a response. It was just no-one could tell me what was best for MAF cleaning.
So, Update, Fresh Fuel, Checked the fitting of all leads, Taken for a good run, and It was better, But by no means cleared.
I had a read up about the MAF, and if it were at fault, the engine would have a dead spot rather than just hesitatuion. so I think that ruled out the MAF being faulty.
So I took onboard everyones advice, and:
I cleaned MAF (Carb cleaner), WD40 round the Dizzy, cleaned along all the HT leads with GT85, Made sure all leads were pressed in place, and cleaned and reoiled the air filter for good measure. Then I took it to get some more fuel and put in some fuel cleaner too.
First the good news.
There was one tiny stutter under load once the engine got warmed, then the car behaved without fault for 170 miles.
Then on the way back from Cambridgshire a coolant hose let go at a healthy speed on the M11. Spent 6 hours getting home. The RAC had a look, and in the process of removing the offending hose, split the crack pipe, so it was then a flatbed back home.
So at least I know the hesitation is gone, (for now).
To surmise, Carb cleaner seemed not to kill the MAF wire.
BTW John, have you still got an ar$edent in your track monster VR6?
Sorry, Had loads of other stuff on the go.
I usually post for the Corrado on the corrado forum, as, from experience there is a higher chance of a response. It was just no-one could tell me what was best for MAF cleaning.
So, Update, Fresh Fuel, Checked the fitting of all leads, Taken for a good run, and It was better, But by no means cleared.
I had a read up about the MAF, and if it were at fault, the engine would have a dead spot rather than just hesitatuion. so I think that ruled out the MAF being faulty.
So I took onboard everyones advice, and:
I cleaned MAF (Carb cleaner), WD40 round the Dizzy, cleaned along all the HT leads with GT85, Made sure all leads were pressed in place, and cleaned and reoiled the air filter for good measure. Then I took it to get some more fuel and put in some fuel cleaner too.
First the good news.
There was one tiny stutter under load once the engine got warmed, then the car behaved without fault for 170 miles.
Then on the way back from Cambridgshire a coolant hose let go at a healthy speed on the M11. Spent 6 hours getting home. The RAC had a look, and in the process of removing the offending hose, split the crack pipe, so it was then a flatbed back home.
So at least I know the hesitation is gone, (for now).
To surmise, Carb cleaner seemed not to kill the MAF wire.
BTW John, have you still got an ar$edent in your track monster VR6?
Nope the famous "arse print" drivers door (caused when a friend tried to bump the car off a jack which couldn't be pulled from under the car and was subject of much hilarity at VW shows for three years) is now replaced. The car also isn't blue anymore (see my profile for evidence of both)
I have to say I disagree with what you said about the MAF just causing a flat spot. If there is a problem with a connection either inside the MAF or the connecting plug the engine will definately stutter because the signal to the ECU won't be consistant. It could run flat as well, but for other reasons.
But it sounds like you're hitting the correct part of the car with your cleaning policy. Sounds like a bit more might make it perfect.
I hope the RAC agree to buy you a new crackpipe for the one they damaged. Not sure if you've seen this before but let me tempt you with this
John
I have to say I disagree with what you said about the MAF just causing a flat spot. If there is a problem with a connection either inside the MAF or the connecting plug the engine will definately stutter because the signal to the ECU won't be consistant. It could run flat as well, but for other reasons.
But it sounds like you're hitting the correct part of the car with your cleaning policy. Sounds like a bit more might make it perfect.
I hope the RAC agree to buy you a new crackpipe for the one they damaged. Not sure if you've seen this before but let me tempt you with this
John
You REALLY need to get the car plugged into VAGCom rather than just guessing at it. My VR6 had a odd hesitancy at around 3000rpm and wouldnt pull 100% cleanly through the revs. There were a couple of niggles and i can assure you without VAGCOM i could have pent shed loads of cash buying parts galore based on some suggestions. It turned out to be a combination of faults
1) the inlet manifold temperature sensor
2) a broken wire on the throttle body
3) a load of other fault codes on the ECU that had been caused by wrong readings being sent to other sensors via the 2 components above.
1 resoldered wire and one new plug on a sensor and at the same time a remap ( i HIGHLY recommend D&G auto nr Birmingham) and the engine is transformed, pulls smoothly and freely right around to its new rev limit :-)
DAVE
1) the inlet manifold temperature sensor
2) a broken wire on the throttle body
3) a load of other fault codes on the ECU that had been caused by wrong readings being sent to other sensors via the 2 components above.
1 resoldered wire and one new plug on a sensor and at the same time a remap ( i HIGHLY recommend D&G auto nr Birmingham) and the engine is transformed, pulls smoothly and freely right around to its new rev limit :-)
DAVE
Gassing Station | Audi, Seat, Skoda & VW | Top of Page | What's New | My Stuff


