Increase the power and RPM of an engine
Discussion
Hello fellow piston headers!!
I'm in my second year of Uni studying Mechanical Engineering and we have been assigned the ridiculously boring task of reverse engineering a Honda GX160 engine and then finding ways to increase the power of the overall engine by 50% and increasing the RPM's by 35%.
Could someone please help me out and give me ideas of what i should be looking at to achieve this new spec?
Thanks,
James
I'm in my second year of Uni studying Mechanical Engineering and we have been assigned the ridiculously boring task of reverse engineering a Honda GX160 engine and then finding ways to increase the power of the overall engine by 50% and increasing the RPM's by 35%.
Could someone please help me out and give me ideas of what i should be looking at to achieve this new spec?
Thanks,
James
Stronger lighter internals, better balanced too. If you can increase the RPM you'll increase the power as long as it's still making similar torque.
Or have a think about it as you're the one doing a degree.
PS. if you think that's boring you should try getting a real job.
Or have a think about it as you're the one doing a degree.

PS. if you think that's boring you should try getting a real job.

Edited by nonuts on Monday 24th January 19:16
snoopios said:
studying Mechanical Engineering and we have been assigned the ridiculously boring task of reverse engineering a Honda GX160 engine
Methinks Sir has chosen the wrong course!? Anyway - basically you need to make it more efficient, gases in, gases out. Blue printed, lightened, balance internals etc, to enable higher revs, and with higher revs comes higher power.
I've got a few things down already but i somehow doubt its everything and this was more to get some new/other ideas/ways to do it;
1. Reduce the weight of the parts
2. Increase cylinder bore
3. Reduce clearance volume?
4. Cam timings
5. Valve lift - increasing valve lobe length
6. Ignition timings
7. Stronger valve springs
8. Valve lobe dimensions for how long the valve is open for
Haha, i am actually trying to get an Industrial Placement at the moment which will hopefully lead to a job
Already had 3 interviews so fingers crossed!!
There isn't actually any "budget" or something along those lines, it's all theoretical which makes it even more dull cause we don't get to build anything
1. Reduce the weight of the parts
2. Increase cylinder bore
3. Reduce clearance volume?
4. Cam timings
5. Valve lift - increasing valve lobe length
6. Ignition timings
7. Stronger valve springs
8. Valve lobe dimensions for how long the valve is open for
Haha, i am actually trying to get an Industrial Placement at the moment which will hopefully lead to a job
Already had 3 interviews so fingers crossed!!There isn't actually any "budget" or something along those lines, it's all theoretical which makes it even more dull cause we don't get to build anything

snoopios said:
I've got a few things down already but i somehow doubt its everything and this was more to get some new/other ideas/ways to do it;
1. Reduce the weight of the parts
2. Increase cylinder bore
3. Reduce clearance volume?
4. Cam timings
5. Valve lift - increasing valve lobe length
6. Ignition timings
7. Stronger valve springs
8. Valve lobe dimensions for how long the valve is open for
Haha, i am actually trying to get an Industrial Placement at the moment which will hopefully lead to a job
Already had 3 interviews so fingers crossed!!
There isn't actually any "budget" or something along those lines, it's all theoretical which makes it even more dull cause we don't get to build anything
Job number 1 is step 2 on your list. How much can it be bored out by?1. Reduce the weight of the parts
2. Increase cylinder bore
3. Reduce clearance volume?
4. Cam timings
5. Valve lift - increasing valve lobe length
6. Ignition timings
7. Stronger valve springs
8. Valve lobe dimensions for how long the valve is open for
Haha, i am actually trying to get an Industrial Placement at the moment which will hopefully lead to a job
Already had 3 interviews so fingers crossed!!There isn't actually any "budget" or something along those lines, it's all theoretical which makes it even more dull cause we don't get to build anything

If you actually have a target of raising the RPMs by 35% you're going to have to look at making the engine breate better too - these things tend to run out of puff quite fast.
(honda GX160, for those who don't know, is a single pot 4-stroke aircooled engine, often found on low-end go karts, electrical generators etc etc.) 5.5bhp, right?
C
C
Hve you actaully got to build the engine and prove it, or just do the calulations?
Because to build it and run it is going to cost a lot of money. Its going to need the head ports cleaned up, probably bigger valves, a custom camshaft. Then theres the bottom end, the crank might be ok, but I reckon you'll need rods, pistons and flywheel to increase the rpm by that much.
Because to build it and run it is going to cost a lot of money. Its going to need the head ports cleaned up, probably bigger valves, a custom camshaft. Then theres the bottom end, the crank might be ok, but I reckon you'll need rods, pistons and flywheel to increase the rpm by that much.
boredofmyoldname said:
nonuts said:
PS. if you think that's boring you should try getting a real job. 
Just what I was thinking, it sounds like the kind of thing some PHers would try to work out after a few beers in their shed. 

CraigyMc said:
snoopios said:
I've got a few things down already but i somehow doubt its everything and this was more to get some new/other ideas/ways to do it;
1. Reduce the weight of the parts
2. Increase cylinder bore
3. Reduce clearance volume?
4. Cam timings
5. Valve lift - increasing valve lobe length
6. Ignition timings
7. Stronger valve springs
8. Valve lobe dimensions for how long the valve is open for
Haha, i am actually trying to get an Industrial Placement at the moment which will hopefully lead to a job
Already had 3 interviews so fingers crossed!!
There isn't actually any "budget" or something along those lines, it's all theoretical which makes it even more dull cause we don't get to build anything
Job number 1 is step 2 on your list. How much can it be bored out by?1. Reduce the weight of the parts
2. Increase cylinder bore
3. Reduce clearance volume?
4. Cam timings
5. Valve lift - increasing valve lobe length
6. Ignition timings
7. Stronger valve springs
8. Valve lobe dimensions for how long the valve is open for
Haha, i am actually trying to get an Industrial Placement at the moment which will hopefully lead to a job
Already had 3 interviews so fingers crossed!!There isn't actually any "budget" or something along those lines, it's all theoretical which makes it even more dull cause we don't get to build anything

If you actually have a target of raising the RPMs by 35% you're going to have to look at making the engine breate better too - these things tend to run out of puff quite fast.
(honda GX160, for those who don't know, is a single pot 4-stroke aircooled engine, often found on low-end go karts, electrical generators etc etc.) 5.5bhp, right?
C
C

And yeah, you've got it spot on with the description of the engine we are using. That's why Nitrous and Turbo/Super Chargers wouldn't be a great way to do what we are doing

Megaflow said:
Hve you actaully got to build the engine and prove it, or just do the calulations?
Because to build it and run it is going to cost a lot of money. Its going to need the head ports cleaned up, probably bigger valves, a custom camshaft. Then theres the bottom end, the crank might be ok, but I reckon you'll need rods, pistons and flywheel to increase the rpm by that much.
Nope, it's all theoretical, no build needed at all!!Because to build it and run it is going to cost a lot of money. Its going to need the head ports cleaned up, probably bigger valves, a custom camshaft. Then theres the bottom end, the crank might be ok, but I reckon you'll need rods, pistons and flywheel to increase the rpm by that much.
Gassing Station | General Gassing | Top of Page | What's New | My Stuff




