Triumph mechanical help please
Discussion
Hi
In need of a little mechanical advice, i brought a Triumph 955i Daytona (03 plate) in January and rode it back from Scotland. The owner said it had been sitting around for a few months unused so I got hold of some forte and flushed it through the system to give it a clean on the run back.
Anyway after about a month thought it could do with a service so, changed the oil, oil filter, plugs, couldn’t get hold of an air filter so gave the old one a good clean, changed the nylons on the fuel tank and the rubber o rings. But after I put it all back together it wont start, we have checked that there is a spark from the plugs, we have checked the jets are not blocked and that the fuel is getting through, checked the compression in the engine, checked all the connectors and relays but it still wont start.
We think its a fuel issue because if we pour fuel or easy start into the pots themselves it does fire and runs but then when we put it back together it wont turn over. We have tried pouring fuel into the pots and then putting it back together to see if that will help but it just fires and burns the fuel in the pots.
Any ideas?
Make sure the fuel is getting as far as the fuel pump. Then dissconnect the fuel pipe on the other side of the fuel pump to make sure it's getting through. Then take it stage by stage after that until you reach the point where it stops flowing. Is it possible you've connected the fuel pump back to front? Is there an inline fuel filter that is one way flow. If you work out what it isn't then you'll find the answer. I'm working on a Triumph today so I'll see if anything is obvious.
thanks guys, we didnt change the fuel filter because its like a little bag on the inside of the fuel tank and was advised not to bother.
the fuel is getting as far as the injectors and the injectors are working (we gave them a clean with an air line), we took them out and placed them on top off the pots and tried to start it, the fuel was getting through the injectors so they arent blocked and they are openeing.
the fuel is getting as far as the injectors and the injectors are working (we gave them a clean with an air line), we took them out and placed them on top off the pots and tried to start it, the fuel was getting through the injectors so they arent blocked and they are openeing.
Do you have the leads to the injectors back in the correct order?
How about the plug leads?
You have fuel at the injectors, you have sparks at the plugs so it should run.
The only way it wouldn't is if you have these things in the wrong order so you don't have both together in the cylinder at the same time.
How about the plug leads?
You have fuel at the injectors, you have sparks at the plugs so it should run.
The only way it wouldn't is if you have these things in the wrong order so you don't have both together in the cylinder at the same time.
yeah the injectors are connected in the right order.
no water in the fuel tank, and we cleaned the airfilter with an airline and some spray.
thinking of disconecting the ecu and letting it reset itself.
its a bit confusing because the sparks are working and the fuel is getting to the injectors but for some reason it just isnt turning over.
no water in the fuel tank, and we cleaned the airfilter with an airline and some spray.
thinking of disconecting the ecu and letting it reset itself.
its a bit confusing because the sparks are working and the fuel is getting to the injectors but for some reason it just isnt turning over.
Thesius said:
thinking of disconecting the ecu and letting it reset itself.
Isn't ECU reset on Triumph's a certain number of start cycles or something?If you're getting spark and fuel she should go. Just had situation you describe with a mate's bike and it was water in fuel. Trying lighting stuff coming out of injectors (in a separate vessel, wearing health and safety steel toe-capped flouro pj's etc)
Wasn't a paper filter you cleaned with airline and spray was it? Leave it out for one test, easy enough to do.
the starter motor isnt turning the engine over normaly but if we pour fuel into the pots then the starter motor does turn it over and it does fire.
we checked the fuel the other day and it seems fine, both visualy and when we dropped a match on a small amount it went up quick enough.
we dont think the jets are firing enough fuel through, so there is fuel getting into the cylinder but not enough for it to fire.
we have a mechanic coming over on wednesday to have a poke around and see what he can find out, just hope its ready for sunday as there are about 30 of us going to the wootton bassett ride.
we checked the fuel the other day and it seems fine, both visualy and when we dropped a match on a small amount it went up quick enough.
we dont think the jets are firing enough fuel through, so there is fuel getting into the cylinder but not enough for it to fire.
we have a mechanic coming over on wednesday to have a poke around and see what he can find out, just hope its ready for sunday as there are about 30 of us going to the wootton bassett ride.
Thesius said:
the starter motor isnt turning the engine over normaly
I'm a bit confused here? Is it turning the engine quickly, slowly or not at all? Have you charged the battery up (Probably already mentioned but its always my first port of fault diagnostics) Have you tried jump starting it? It sounds to me like its not spinning fast enough to catch?Hi just wondering if you got to the bottom of your problem as i'm having the same issue.
all I did though was take the tank and fairing off for paint,.. the battery was disconnected briefly also.
just not having any luck getting it started, could you shed some light on it as i'm stumped, any help would be greatly appreciated.
Cheers, Aaron.
all I did though was take the tank and fairing off for paint,.. the battery was disconnected briefly also.
just not having any luck getting it started, could you shed some light on it as i'm stumped, any help would be greatly appreciated.
Cheers, Aaron.
Gassing Station | Biker Banter | Top of Page | What's New | My Stuff


