Bmw 130i project
Discussion
M77MWW said:
fantastic read so far mate!!! your not too far away either, I'm only down the a2 by Bexleyheath. what times you done at the ring
I pass bexleyheath nearly everyday. I'm starting to learn where every bump is on the a2 between london and rochester :-DI've never timed myself around there for some reason, might do in the future
vMPM said:
Best looking E87 I've seen! This car is going to be nuts when it is finished, awesome project!
sjj84 said:
Pretty impressive so far, will be ace when finished.
thanks for the commentsNo updates as the car has been away getting the DTA and Race technology dash wired up, should be back at the weekend.
Some pics from before it went away
Clutch from CG Motorsport, all fitted
Had an accident, let the jack down with an axle stand underneath
Had a -6 jic fitting welded to the fuel rail and made up a fuel line for my braided hose to go onto, tight fit!!!
got the car in a position to be taken away for wiring
car was too wide for the trailer so had to fit a space saver back to front and just squeezed on with mm to spare!!
Also got rid of the Eos and picked up a Passat CC for my daily
Some pics from before it went away
Clutch from CG Motorsport, all fitted
Had an accident, let the jack down with an axle stand underneath
Had a -6 jic fitting welded to the fuel rail and made up a fuel line for my braided hose to go onto, tight fit!!!
got the car in a position to be taken away for wiring
car was too wide for the trailer so had to fit a space saver back to front and just squeezed on with mm to spare!!
Also got rid of the Eos and picked up a Passat CC for my daily
After just over a month i got the car back last saturday. Went back over to track and road and got trailered back
Wiring all completed
ECU mounted
Have a problem with my race technology dash. Seems to have a firmware issue. Been sent away so hopefully will get it back next week
Picked up a 1M exhaust from birmingham last sunday and trial fitted it. I had to cut off the end's that attach to the downpipes and use the E46 Flanges. All lines up ok so will fit it proper over the next week or so
Where do i start with this thing!!!
I got to the point where i was a days work from starting it and then remembered from when i took it out the M3 that it had a misfire so decided to check everything before start up.
Its then i realised why it had misfire
Decided to stick a camera down the bores and although the crowns didn't look too bad they weren't great either so i done a compression test. Cylinders 2+3 come back low
At that point i decided to strip the engine down before deciding what way to go with it
I've decided i will probably fit JE piston's, standard rods, race bearings, and all ARP bolts. Just getting the funds together for the build at the moment though.
Managed to get hold of a 1M bumper for cheap so i can run 265 section up front eventually.
Made a start on the rear's. already running 10j ET23 on the rear but now have spacers
Got hold of an 60l ATL fuel cell. I was going to mount it up where the boot was but decided against having the weight high up so chopped the rear bench away and got started on mounting it lower to help with handling.
In-between all that i took the daily out to the ring for a few laps while i was out in Belguim
Updates as and when, not looking to get it up and running until feb next year now though
I got to the point where i was a days work from starting it and then remembered from when i took it out the M3 that it had a misfire so decided to check everything before start up.
Its then i realised why it had misfire
Decided to stick a camera down the bores and although the crowns didn't look too bad they weren't great either so i done a compression test. Cylinders 2+3 come back low
At that point i decided to strip the engine down before deciding what way to go with it
I've decided i will probably fit JE piston's, standard rods, race bearings, and all ARP bolts. Just getting the funds together for the build at the moment though.
Managed to get hold of a 1M bumper for cheap so i can run 265 section up front eventually.
Made a start on the rear's. already running 10j ET23 on the rear but now have spacers
Got hold of an 60l ATL fuel cell. I was going to mount it up where the boot was but decided against having the weight high up so chopped the rear bench away and got started on mounting it lower to help with handling.
In-between all that i took the daily out to the ring for a few laps while i was out in Belguim
Updates as and when, not looking to get it up and running until feb next year now though
ManOpener said:
Wide arches too
Love this build.
Wide arches wasn't the plan but coming across the 1M bumper has forced my hand Love this build.
helix402 said:
Had the head gasket failed on the M3 engine?
It has yes. I knew it was misfiring but it had electrical issues so put it down to that. I'm glad i never investigated the issue back when i had the M3 as i doubt i would of done the conversion so i'm not complaining jaacck said:
I don't usually post but made a special effort to log in to say that this is awesome. bookmarked
I appreciate that mate, always nice to read peoples comments and other peoples perspectives on the build DELETED: Comment made by a member who's account has been deleted.
Thanks mate appreciate that, i'm so looking forward to getting it done
Gassing Station | Readers' Cars | Top of Page | What's New | My Stuff