"Gentlemen, show your engines!"
Discussion
Pupp said:
Not hoes, or even hose, but 15mm stainless pipe simply bent to pick up the relevant hoses at either end - see top of p2 on this thread and look just to the side of the thermostat housing which is where one pipe is picked up (2x 90deg elbows with an ally joiner but a preformed 'u' bend would do just as well. Need decent madrel benders to form the pipe to the right shape but get it right and it can be threaded through the under manifold void without having to disturb anything. Well worth doing just for the better spanner clearance on the drivers side and the ability to pop the rocker cover off with no drama
Good call I did the same looks much neater IMO ![thumbup](/inc/images/thumbup.gif)
spend said:
Still better if you plumb into the water pump rather than running all the way to the swan neck ![wink](/inc/images/wink.gif)
..and use a preserp inlet manifold![rofl](/inc/images/rofl.gif)
Is that all Dave? just the pre-serp inlet that's needed apart from the mods to the pump obviously ![wink](/inc/images/wink.gif)
..and use a preserp inlet manifold
![rofl](/inc/images/rofl.gif)
![wink](/inc/images/wink.gif)
![frown](/inc/images/frown.gif)
![biggrin](/inc/images/biggrin.gif)
![scratchchin](/inc/images/scratchchin.gif)
![](http://thumbsnap.com/sc/EvF4shmx.jpg)
![hehe](/inc/images/hehe.gif)
Edited by Simon says on Thursday 26th May 22:41
You could simply tap into the bottom of the serp manifold I suppose (behind where the serp temp sender is) and screw in a hose tail or threaded pipe just like the pre-serp.
You just need to think what effect flow passing over the temp sensor means and how to keep air away from the tip...
You just need to think what effect flow passing over the temp sensor means and how to keep air away from the tip...
spend said:
You could simply tap into the bottom of the serp manifold I suppose (behind where the serp temp sender is) and screw in a hose tail or threaded pipe just like the pre-serp.
You just need to think what effect flow passing over the temp sensor means and how to keep air away from the tip...
nice one,I use the stock LR sensor with a variable resistor(I only want to see running temp on the gauge) so that should not be an issue,certainly seems a possibility best dig out my spare inlet and let you know how I get on You just need to think what effect flow passing over the temp sensor means and how to keep air away from the tip...
![wink](/inc/images/wink.gif)
Simon says said:
spend said:
You could simply tap into the bottom of the serp manifold I suppose (behind where the serp temp sender is) and screw in a hose tail or threaded pipe just like the pre-serp.
You just need to think what effect flow passing over the temp sensor means and how to keep air away from the tip...
nice one,I use the stock LR sensor with a variable resistor(I only want to see running temp on the gauge) so that should not be an issue,certainly seems a possibility best dig out my spare inlet and let you know how I get on You just need to think what effect flow passing over the temp sensor means and how to keep air away from the tip...
![wink](/inc/images/wink.gif)
spend said:
Simon says said:
spend said:
You could simply tap into the bottom of the serp manifold I suppose (behind where the serp temp sender is) and screw in a hose tail or threaded pipe just like the pre-serp.
You just need to think what effect flow passing over the temp sensor means and how to keep air away from the tip...
nice one,I use the stock LR sensor with a variable resistor(I only want to see running temp on the gauge) so that should not be an issue,certainly seems a possibility best dig out my spare inlet and let you know how I get on You just need to think what effect flow passing over the temp sensor means and how to keep air away from the tip...
![wink](/inc/images/wink.gif)
![scratchchin](/inc/images/scratchchin.gif)
![wink](/inc/images/wink.gif)
Edited by Simon says on Saturday 28th May 00:29
Tidy
don't take this as a criticism but I would advise something more substantial for the swirl pot to expansion bottle hose than a cable tie the heat from the exhaust will ruin that in short time including your hose,I formed a nicer one from a stainless CV boot clip,different what you have done for the swirl pot & expansion bottle too ![wink](/inc/images/wink.gif)
![thumbup](/inc/images/thumbup.gif)
![wink](/inc/images/wink.gif)
Hi Simon, thanks for that, no I don't mind critisism I encourage it providing it's constructive as it's the only way to make improvements. I'm working on some better ring fixings in Black to replace the plastic tie-wraps.My expantion bottle now has a lovely shiny Leven top on it and it looks the biz.
Simon says said:
Tidy
don't take this as a criticism but I would advise something more substantial for the swirl pot to expansion bottle hose than a cable tie the heat from the exhaust will ruin that in short time including your hose,I formed a nicer one from a stainless CV boot clip,different what you have done for the swirl pot & expansion bottle too ![wink](/inc/images/wink.gif)
![thumbup](/inc/images/thumbup.gif)
![wink](/inc/images/wink.gif)
Gassing Station | Chimaera | Top of Page | What's New | My Stuff