head gasket failure prompts winter rebuild
Discussion
No worries mate, I used to be a skier, saw the light lol.
To bring it back on topic, I drove the noble today for the first time since the head gasket failed at Silverstone. So happy; No leaks which is cool. Up to temp with the fans kicking in and the exhaust isn't kicking out any smoke :-). Just a bit of tidying up tomorrow...
To bring it back on topic, I drove the noble today for the first time since the head gasket failed at Silverstone. So happy; No leaks which is cool. Up to temp with the fans kicking in and the exhaust isn't kicking out any smoke :-). Just a bit of tidying up tomorrow...
2.5bluenob said:
just got back from a skiing holiday and all i can say is dam snowboarders always in the way!
p.s Sorry for taking off topic again james but missed these comments coz i was plaing in the white stuff.
steve
Just got back from Arc 1950... great fun but looking forward to getting my Nob out this afternoon!p.s Sorry for taking off topic again james but missed these comments coz i was plaing in the white stuff.
steve
did another 70miles in the Noble on Sunday and no leaks/smoke/misfires etc, all good.
here's a couple of pics of the gearlinkage work i did. still haven't finished the top plate/gaiter but here was the hard work.
The square i cut into the top of the tunnel to drop the gear lever assy into place
here's the jetstream bracket in place inside the tunnel with the cables attached.
here you can see the two bolts holding the tunnel bracket in place on the drivers side. also you can see where i drilled the holes for the lever bracket before deciding to drop it lower in the tunnel. please with the final height of the gear lever
here's a couple of pics of the gearlinkage work i did. still haven't finished the top plate/gaiter but here was the hard work.
The square i cut into the top of the tunnel to drop the gear lever assy into place
here's the jetstream bracket in place inside the tunnel with the cables attached.
here you can see the two bolts holding the tunnel bracket in place on the drivers side. also you can see where i drilled the holes for the lever bracket before deciding to drop it lower in the tunnel. please with the final height of the gear lever
yes the gearchange is transformed over the old ball and rod lol
One tip for future people... cut the carpet along the top of the tunnel you can the peal it back down the sides.... due to the size of the mechanism you have to also make an all new gear gaitor like the GT03R which covers the entire top of tunnel and thus hides all the cuts in the carpet
One tip for future people... cut the carpet along the top of the tunnel you can the peal it back down the sides.... due to the size of the mechanism you have to also make an all new gear gaitor like the GT03R which covers the entire top of tunnel and thus hides all the cuts in the carpet
Jamescmr2 said:
key750 said:
excuse me you know which car comes from this gearlever?
(just to add extra work for my winter...)
If you speak to Jetstream they will be able to help you. I recommend you buy their kit if you are looking at this upgrade(just to add extra work for my winter...)
cheers
As james has siad, unless you know exactly what goes in the kit and can fabricate it all, your only real option is to buy the kit.
andygtt said:
its mondeo... but the lever itself is useless on it's own... you need all the cables and brackets in tunnel, plus the gearlever itself is modified.
As james has siad, unless you know exactly what goes in the kit and can fabricate it all, your only real option is to buy the kit.
Thanks for the clue, looks something like this?As james has siad, unless you know exactly what goes in the kit and can fabricate it all, your only real option is to buy the kit.
I love to do it myself and if the cable length is not much different I can stretch with the threaded rod.
I want to run the cables above the gearbox and not above the cylinder (as now) so I will take a little time because I have to rebuild the bracket near the turret gear.
i can honestly say upgrading the gear linkage is one of the best things i have ever done on the car. My old gear change was a bit sloppy, "it's in there somewhere", and now it's tight and notchy in a good way. my mate drove my car before the rebuild and after and he was amazed at the difference. maybe i had a bad gear linkage before but from what i hear others were similar!
Jetstream do not have a website, from what i understand they have too much business from word of mouth. If you want to get in touch drop me an email and i will forward contact details. They are based at Bruntingthorpe Airfield.
here is a pic of the gear stick and bracket (http://www.pistonheads.com/gassing/topic.asp?h=0&f=26&t=1091482&mid=166257&i=40&nmt=New+shifter+linkage+&mid=166257). look at my post
this comes as a complete unit and you chop the bottom off before fitting. the gear stick has a slightly larger thread on than the original Noble one but i am going to work a way of getting the old gear knob to fit (maybe just run a tap down it).
cheers
James
Jetstream do not have a website, from what i understand they have too much business from word of mouth. If you want to get in touch drop me an email and i will forward contact details. They are based at Bruntingthorpe Airfield.
here is a pic of the gear stick and bracket (http://www.pistonheads.com/gassing/topic.asp?h=0&f=26&t=1091482&mid=166257&i=40&nmt=New+shifter+linkage+&mid=166257). look at my post
this comes as a complete unit and you chop the bottom off before fitting. the gear stick has a slightly larger thread on than the original Noble one but i am going to work a way of getting the old gear knob to fit (maybe just run a tap down it).
cheers
James
Edited by Jamescmr2 on Thursday 1st March 12:17
Hi.
I'm Mondeo ST220 user.
After head gasket failed in my Duratec 3.0, I've noticed it's "blue" and looks the same like Jamescmr2 wrong gasket
Jamescmr2 story probably explains why "blue" OEM gaskets fail so often even in naturally aspirated Mondeos ST220!
I've bought new gasket set from Victor Reinz and they are "black"!
Like the correct ones in Noble - It looks identical.
This should solve Mondeo ST220 notorious problem, I guess.
p/n: 60-36880-00
p/n: 60-36875-00
direct comparison:
I'm Mondeo ST220 user.
After head gasket failed in my Duratec 3.0, I've noticed it's "blue" and looks the same like Jamescmr2 wrong gasket
Jamescmr2 story probably explains why "blue" OEM gaskets fail so often even in naturally aspirated Mondeos ST220!
I've bought new gasket set from Victor Reinz and they are "black"!
Like the correct ones in Noble - It looks identical.
This should solve Mondeo ST220 notorious problem, I guess.
p/n: 60-36880-00
p/n: 60-36875-00
direct comparison:
Gassing Station | Noble | Top of Page | What's New | My Stuff