2005 Volvo V70 2.5T SE
Discussion
I gave Kära her first wash of 2024 today, she's safely and comfortably transported me up to the highlands twice and was covered in salt. Wheel arches were rinsed with particular attention paid to the strut towers.
Once clean I decided to go for a drive to dry her off and stopped for a few pics...
Once clean I decided to go for a drive to dry her off and stopped for a few pics...
@ cptsideways. Great picture of an XC70 doing what it's supposed to do
Winter is officially over even though there is still a ground frost in the mornings putting my Gladioli in danger. The summer Thor wheels and Goodyear tyres are back on in anticipation of warmer times.
Winter Mimas 16"
Summer Thor 17"
Never been refurbished and still on the original factory finish
Winter is officially over even though there is still a ground frost in the mornings putting my Gladioli in danger. The summer Thor wheels and Goodyear tyres are back on in anticipation of warmer times.
Winter Mimas 16"
Summer Thor 17"
Never been refurbished and still on the original factory finish
Yes Mad Maximus, the ride is smoother over the pothole ridden roads with the 16" wheels and taller sidewalls, the cornering is more taught at speed with the 17" wheels. If the car was factory fitted with 16" wheels I wouldn't rush out to change them for 17s, I'm too old to worry about high speed cornering and prefer my comfort now
Today I cleaned the Mimas wheels ready for storing until the autumn.
An elderly neighbour gave me a bottle of Greased Lightning Showroom Shine 5 or 6 years ago and it's been sitting on a garage shelf ever since, so today I decided to try it on the inside of the wheels. I am thoroughly impressed with the results, it removed all the winter salt, tar spots and rust marks caused by the discs and they wheels look great again. No I wouldn't use it on the paintwork but for the inside of the wheels it is perfect
An elderly neighbour gave me a bottle of Greased Lightning Showroom Shine 5 or 6 years ago and it's been sitting on a garage shelf ever since, so today I decided to try it on the inside of the wheels. I am thoroughly impressed with the results, it removed all the winter salt, tar spots and rust marks caused by the discs and they wheels look great again. No I wouldn't use it on the paintwork but for the inside of the wheels it is perfect
On October I posted that I had cured my ABS-0136 Brake Pressure Sensor fault and it's been working fine until last week. The code came back and this time it was reluctant to reset, I eventually managed to clear it but on Tuesday it appeared again and wouldn't turn off so I managed to find someone local who is breaking a car and bought two sensors from him after speaking to Volvo Parts and getting quoted £300 + VAT for each sensor.
My live data showed sensor 1 was 4.56, sensor 2 was -0.91 and my scanner told me sensor 1 was at fault. I unplugged sensor 1 and connected it to the replacement sensor and went back to live data which showed both sensors were reading similar to each other and within the parameters allowed so I decided to swap sensor 1 over today.
Before starting I primed the sensor with a few drops of fresh brake fluid, I removed the cross brace, I placed a piece of Cling Film on the reservoir and used an elastic band to hold it tightly in place, a 27mm long socket removed the sensor and the replacement was screwed in and torqued to 25NM. Wire harness attached and live data checked and everything is once again working as it should.
Live data readings for good sensors
My live data showed sensor 1 was 4.56, sensor 2 was -0.91 and my scanner told me sensor 1 was at fault. I unplugged sensor 1 and connected it to the replacement sensor and went back to live data which showed both sensors were reading similar to each other and within the parameters allowed so I decided to swap sensor 1 over today.
Before starting I primed the sensor with a few drops of fresh brake fluid, I removed the cross brace, I placed a piece of Cling Film on the reservoir and used an elastic band to hold it tightly in place, a 27mm long socket removed the sensor and the replacement was screwed in and torqued to 25NM. Wire harness attached and live data checked and everything is once again working as it should.
Live data readings for good sensors
Gassing Station | Readers' Cars | Top of Page | What's New | My Stuff