What did you do in the garage yesterday?
Discussion
Pupp said:
For QBee
My contribution today is the addition of a single Quik-latch mini on the nearside bonnet corner. Lift and clatter now you sod!
Ey thankyou..... My contribution today is the addition of a single Quik-latch mini on the nearside bonnet corner. Lift and clatter now you sod!
I find that having the splitter fitted underneath, plus tightening the bonnet catch, stopped my bonnet flapping (and popping open at 135 mph)
Hi, just started the process of building the chassis back up, 'twas in the garage this afternoon and rebuilt one of the front assembly's. When I put the top ball joint in the wishbone it doesn't have full range for camber adjustments as the casting of the ball joint hits the wishbone, anyone had this sort of issue? I'm hoping there is enough adjustment when I get it set up.
Are there some tips for setup just till I get it somewhere for a 4wheel alignment?
.
Are there some tips for setup just till I get it somewhere for a 4wheel alignment?
.
Twistygit said:
Hi, just started the process of building the chassis back up, 'twas in the garage this afternoon and rebuilt one of the front assembly's. When I put the top ball joint in the wishbone it doesn't have full range for camber adjustments as the casting of the ball joint hits the wishbone, anyone had this sort of issue? I'm hoping there is enough adjustment when I get it set up.
Are there some tips for setup just till I get it somewhere for a 4wheel alignment?
.
Did you note the geometry measurements before you took it apart? Are there some tips for setup just till I get it somewhere for a 4wheel alignment?
.
This morning a weedy but important little spring rated at a nominal 1.5 psi was swapped for a slightly sturdier but still conservative one rated at 3 psi... and a resistor was added to the fuel level sender circuit to hopefully encourage my SPA gauge to sort its act out (looks promising at last)
Pupp said:
This morning a weedy but important little spring rated at a nominal 1.5 psi was swapped for a slightly sturdier but still conservative one rated at 3 psi... and a resistor was added to the fuel level sender circuit to hopefully encourage my SPA gauge to sort its act out (looks promising at last)
seeby said:
phazed said:
What type of paint did you use Colin, looks good!
I need to do my road set.
Looking forward to showing you the way round on the 29th
Just ordinary car paint Peter. Coloured base coat and then 2 coats of 2pack laquer. Looking forward to Snetts . I need to do my road set.
Looking forward to showing you the way round on the 29th
J400GED said:
Did you note the geometry measurements before you took it apart?
I didn't, I just thought I'd take it for alignment after it was tested. I think its mainly the castor I was curious with. I tried the old ball joint in the wishbone and it also had limited movement in the slotted camber adjustment Twistygit said:
I didn't, I just thought I'd take it for alignment after it was tested. I think its mainly the castor I was curious with. I tried the old ball joint in the wishbone and it also had limited movement in the slotted camber adjustment
On mine, the cuved part of the upper balljoint sat very close to the upper wishbone and the castor shim (8mm I think) sat in front of the balljoint.macdeb said:
Good news Gary, then 6, then 10 maybe?
Just creeping up on it Mac - with the 1.5 rated spring in a 46mm wastegate, and with the boost controller wound in a turn or so, it was logging consistent 3.6 psi boost levels without any nasties apparent apart from I was running out of headroom on the original injectors. Now got some 440cc jobbies in albeit still at 2.5 bar on the original regulator for now, so will be interesting to see what's occurring now. Can say there's no lag, none Harrytsg said:
Looking good Colin, I should have paid you to do mine
Well Andy, the quality may differ a bit between mine and yours ,but then again I am not a sprayer by trade . I think mine are more than good enough to thrash around on trackdays . As my wheels were 2nd hand, I have just covered up some nasty kerbing marks and got rid of the burnt on brake dust . Gassing Station | Chimaera | Top of Page | What's New | My Stuff