I need a M12 x 1.5mm male brake union for 3/16" pipe. Help!

[montyjohn]

Hi all,
I've been trying to get hold of two M12 x 1.5mm male brake union for 3/16" pipe for a master cylinder using a double flare and not getting anywhere.
Easy in the US. Loads of shops selling them. But the postage cost and time are a bit painful

These guys (http://www.carlton-hydraulics.co.uk/) are the only sellers I have found in the UK but they are not keen posting to a member of the public for such a small order - Product ID - BQ9193

I live in Purley (CR8) - South London.
Does anyone know where I can buy these, online or store?

So far all calls to local shops don't stock them.
They can only sell me M12 x 1mm male unions (wrong pitch).

Any suggestions appreciated

[montyjohn]

stevieturbo said:

What car ?

It's a kit car.
But the brake m/c is from a Mondeo MK5.
I have the unions that came with the m/c but they are for 1/4" pipe.

The other method would be to have a short length of 1/4" pipe, and then a reducer, but then that would mean buying a new flaring tool, and it would look a bit of a mess so that's Option C I think.

Edited by montyjohn on Tuesday 23 November 10:34

[montyjohn]

E-bmw said:

I would say check again exactly what you need as M10 x 1.0 is the most common, in fact I can't remember the last time I saw something different that wasn't american.

I know right. Although M12 is pretty common on m/c. But are usually M12 x 1.0mm.
So I blindly ordered the M12 x 1.0mm to find they don't fit.

Here they are side by side. You have to guess which is which.



I haven't got any thread gauges, but measured 5 threads with calipers at something like 7.4mm. Pretty hard to be precise, but close enough to 1.5mm pitch.

EDIT

Here's an M10 * 1.0mm next to them

Edited by montyjohn on Tuesday 23 November 10:36

Edited by montyjohn on Tuesday 23 November 10:40

[montyjohn]

Just thinking, it could be 1/2" UNF, but they surely wouldn't use that on a 2016 Mondeo?
Also the pitch for 1/2" UNF is 20 TPI according to google so that would be 1.25mm.

[montyjohn]

stevieturbo said:

And will the master even accept a 3/16" pipe/flare, if the intended fitment is 1/4" ?

This is a great question and the first question I had.
I offered up a 3/16" flare to the m/c when I first realised the problem and there seems to be plenty overlap between the flare and the cone on the m/c.
The hole in the cone is 3.9mm dia, compare with an approx ID of 3/16" pipe of 2.9mm. The dia of a flare is about 7mm.
So it should seal, but I have no experience to confirm this.

stevieturbo said:

Routing 1/4" pipe to a suitable adapter then 3/16" would be better.

I may end up having to go down this route anyway to to avoid the wait of shipping across the pond.
My only problem is:
2 x reducers (£34) - https://www.ebay.co.uk/itm/362045651225
1m of kunifer is £7, at least that's cheap.
So I'm looking at £40 + garage time for the 1/4" flares. I could buy the tooling, but I need one end to be bubble, and one double, and I'm probably never going to need /14" again. Hopefully.
A new m/c might be cheaper.

I've found garages in North Wales really helpful, but in South London I've always been disappointing. I'm sure there are helpful ones out there, I've just not found them.

I once asked for a new resister to be soldered onto a AC control unit, I had the resister in hand, autos wanted £300 for this job.
I also took a pair of control arms into a garage to press out a pair of bushes. £80 quote. They just looked up the book time and weren't interested that they don't need to remove or refit the control arms.
Walked away on both occasions and did the work myself.

I think one off work to help the DIYer type isn't worth their time when there's good money to be made swapping people disc pads and tyres.
I'll try anyway and see how I get on.

[montyjohn]

richard sails said:

would this one do?
https://automec.co.uk/collections/fittings/product...

Thanks for taking a look, but I tried them already and they don't have a 3/16" version of that union.